Range of adjustable, pilot operated pressure reducing control valves with ductile iron bodies (blue epoxy coated) EPDM diaphragm and NBR ‘O’-rings. The products are supplied with auxiliary stainless-steel tubing, fittings, strainer, pilot valve and needle valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure 1.5 bar - 8.0 bar. Maximum operating temperature 80°C.
Smart water meter monitor with an integrated motorised shut off valve, piezo electric ultrasonic tranducer and pressure sensor, plastic housing and silicone ‘O’-rings. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies, chromium plated brass ball, PTFE seats and EPDM rubber ‘O’-ring. The products also incorporate a ‘Y’- Patterned stainless steel strainer. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Isolation valve incorporating a brass body (chromium plated) and brass ball (chromium plated). Maximum working pressure 10.0 bar. Cold water use only.
Range of lever operating spherical valves incorporating brass bodies (nickel plated), brass ball (chromium plated) and PTFE seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Aladdin Easyfit Isolator Pro’ valve incorporating a stainless steel body and self cutting blade to enable a connection to a pressurised or wet systems. For use with copper pipe to BS2871 – EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves withDZR brass bodies and EPDM ‘O’-rings and various operating members (see model). Maximum working pressure 32.0 bar (15mm). Maximum working pressure 25.0 bar (35mm). Maximum operating temperature 85°C.
Range of non-rising gate valves with blue epoxy coated ductile iron body and EPDM rubber coated wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C
Range of gate valves with blue epoxy coated ductile iron bodies, a ductile iron wedge encapsulated in EPDM rubber, PTFE seals and EPDM gaskets and ‘O’-rings. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with brass bodies, brass wedges and PTFE packing glands. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of gate valves with blue epoxy resin coated cast iron (DN65-80) or ductile iron (DN100-200) bodies, EPDM coated ductile iron wedge and EPDM gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Cold water use only.
5 way manifold assembly with a DZR brass body incorporating a pressure reducing valve, with an adjustable outlet pressure range between 1.0 and 6.0 bar and a safety relief valve set at 6.0 bar. The product incorporates an inline single check valve cartridge after the balanced cold take off, verified by test (suitable for backflow protection against Fluid Category 2). Maximum supply pressure 16.0 bar. Maximum operating temperature 40°C
Range of polyethylene pressure vessels with spun (blue) fibre glass casing. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
‘Hostaform® C9021 ECO-B NATURAL, C9021, M15HP, C2521, C13021, C13031, C27021 ECO-B NATURAL, C27021, C52021 & M90JG’. Injection moulded, natural (which appear to be white) acetal materials available in the following colours: Black 14 DW (formerly known as Black 14), White 22, Grey 33, Grey 36, Grey 39, Red 46, Red 47, Yellow 56, Brown 65, Green 76, Blue 87, RAL 2010, RAL 4008 & RAL 5005. Customer specific colours may also be provided with a nomenclature following the structure ‘xx/yyyy DW’ where ‘yyyy’ denotes the specific colour shade, ‘DW’ denotes ‘Drinking Water’ & ‘xx’ denotes 10 – black, 20 - white (incl. Cream, 30 – grey, 40 – red (incl. Pink), 50 – yellow, 60 – brown (incl. Beige), 70 – Green & 80 – blue. For use with water up to 65°C.
'Sealcoat Black'. Black coloured, factory applied petroleum bituminous coating. Apply as per manufacturer's instructions for use reference 'PC 819' dated March, 26, 2021. Cure for 18 hours at 30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks.
'AD-995'. White coloured, compression moulded ceramic material. For use with water up to 85°C.
'JH'. Factory applied, blue coloured epoxy powder coating. Heat substrate to 220°C for 30 minutes, spray apply coating and then cure at 190°C for 20 minutes. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the cure and/or application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EUROKOTE® 46-20’. Factory applied, red-brown coloured, two-part epoxy resin coating. Mix and apply as per manufacturer's technical data sheet 'Doc. 087' dated 01/07/2011. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Electroline ES 1212-Black`. Factory applied, black coloured, 2 part epoxy coating. Mix parts A&B in a 3:1 volume ratio. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘SIGMAPRIME 200 for use with SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. SIGMAPRIME 200 (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio. Cure for 3 days@23°C. SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue) is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio. Cure for 12 days@23°C. For use with water up to 23°C.
Page 31 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
