`8601-A`. Extruded, dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. Shore hardness 85. For use with water up to 85°C.
'Addisil WTG 1'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Plustek PA303G6BK16'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'TYPLEX-1055'. Grey coloured, extruded Polybutylene-1 material. For use with water up to 85°C.
'WTST1 Water Tank Sealing Tape'. Black coloured PE foam tape which is adhesive on the non-water contact side. For use with water up to 23°C.
'SP-01 HDPE Fitting'. Black coloured, injection moulded HDPE fittings. For use with water up to 23°C.
'Hostalen CRP100 Black & Hostalen CRP100 RESIST CR Black'. Black coloured HDPE materials, manufactured in Saudi Arabia and Germany, for injection moulding and extrusion purposes. For use with water up to 60°C.
'Revolve N-525 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Helisystem CT fitting'. Green coloured, injection moulded PP-RCT fitting. Between July 2021 and September 2022, the fitting was for use with water up to 23°C. Between October 2022 and July 2026, the fitting is for use with water up to 75°C.
'RTP 499 X 129130 A Natural & RTP 499 X 136502 Natural'. Natural (appear grey in colour), injection moulded polystyrene materials. For use with water up to 50°C.
'Art. 0985077205 Anti-leak Tape'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical data sheet version '001' dated 26.07.2021. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4800'. Site applied, grey coloured cementitious repair mortar. Mix Intercrete 4800 and water in a mass ratio of 7.58:1. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Chemfix 10'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP1/1/6 BLK' O-rings. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 1.75mm. For use with water up to 85°C.
'EP906'. Black coloured, extruded EPDM washer. Shore hardness 90. Tested in-radius size 1.4mm. For use with water up to 85°C.
'ERIKS 55985 Gaskets & ‘O’ rings'. Black coloured, compression moulded EPDM gaskets & ‘O’ rings'. Shore hardness 70A. The gaskets have a tested in-radius size of 1.0mm. The ‘O’ rings have a tested in-radius size of 1.76mm. For use with water up to 85°C.
'CEW50, CEW55, CEW60, CEW65, CEW70, CEW75, CEW80, CEW85 & CEW88'. Black coloured, transfer moulded EPDM rubber materials. Shore hardness between 50 & 88. Tested in-radius size 1.15mm. For use with water up to 60°C.
'CVE45, CVE48, CVE50, CVE52, CVE55, CVE60, CVE61, CVE65, CVE69, CVE70, CVE75, CVE78 & CVE80'. Black coloured, extruded, EPDM materials. Shore hardness between 45 & 80. Tested in-radius size 1.5mm. For use with water up to 60°C.
'AquaFlex T 5817'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 65°C.
Page 29 of 521
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
