Range of drinking water stations. Flow is controlled via a push-button tap assembly (which incorporates a flow regulator) on all models. Model Park Tap 016 0104-TS-016_WRAS incorporates two outlets (bubbler at low-level & bottle filler at high-level). The flexible hose assembly which rises through the body of the station to the lower outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Model Hall TAP_EN (indoor) incorporates one (bottle filler type) outlet with a fixed drip tray under. Street Tap 0104-TS003_WRAS incorporates one (bottle filler type) outlet. The flexible hose assembly which rises through the body of the station to the outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Maximum working pressure 3.5 bar. Cold water use only.

Section:

2425 Water Fountain

Section Subtitle:

Drinking.

WRAS Approval Number:

2207361

Note:

Please note that IRN R006 applies only to model Hall TAP_EN (indoor). This is the only model with a fixed spillover level (in the form of a fixed drip tray).

Size:

8mm push fit

Marking:

Join The Pipe on operating member of tap.

Installation Requirements:

R001 R006 R150 R170 R430

Expiry date:

31/07/2027

Model:

Park Tap 0104-TS016_WRAS. Street Tap 0104-TS003_WRAS. Hall TAP_EN (indoor).

Approval Holder:

Join The pipe

Company Name

Join The pipe

Address

Danzigerbocht 457 1013 AM Amsterdam

Country

Netherlands

View All Listings by this Company

'DURACON® M25-44 WK2001, M90-44 WK2001 & M270-44-WK2001'. White coloured, injection moulded POM materials. For use with water up to 85°C.

Section:

5015 Acetal

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2208530

Expiry date:

31/08/2027

Approval Holder:

Polyplastics Co., Ltd.

Company Name

Polyplastics Co., Ltd.

Address

JR Shinagawa East Building, 18-1, Konan 2-Chome, Minato-Ku, Tokyo, 108-8280

Country

Japan

View All Listings by this Company

`4300314` (grey coloured) & '4300315' (black coloured). Injection moulded ABS material. For use with water up to 85°C.

Section:

5020 Acrylonitrile Butadeine Styrene Copolymer (ABS)

Expiry date:

31/07/2027

Approval Holder:

Zhejiang Kaiyue Plastic Industrial Co., Ltd.

Company Name

Zhejiang Kaiyue Plastic Industrial Co., Ltd.

Address

No 166 Jia Xi Road, Jianshan Town, Pan An Industry Zone, Zhejiang

Country

China

View All Listings by this Company

'Endolac 245.30 FGC'. Factory applied, black coloured, bituminous coating. Apply as per manufacturer's technical data sheet dated 04/05/2022. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5021 Bituminous Based Products

Section Subtitle:

Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials containing petroleum or asphaltic bitumen are not approved for use on water-retaining structures with large surface:volume ratio such as lining of pipes, cisterns or water storage tanks in contact with wholesome water, but may be acceptable for use where there is only a small surface area in contact with the water – e.g. taps, valves and pipe connectors.

WRAS Approval Number:

2208517

Expiry date:

31/08/2027

Approval Holder:

BS Coatings

Company Name

BS Coatings

Address

Allee Paul Sabatier, BP 88, 27940 Aubevoye

Country

France

Phone

+ 33 32773077

View All Listings by this Company

'Eurokote® 448 Bleu 5005 & Eurokote® 448 Bleu 5002'. Factory applied, blue coloured, two-part epoxy coatings consisting of a resin and hardener. Mix resin and hardener in a 1:1 volume ratio and apply as per manufacturer's technical data sheet version dated '29/08/17'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2208515

Expiry date:

31/08/2027

Approval Holder:

BS Coatings

Company Name

BS Coatings

Address

Allee Paul Sabatier, BP 88, 27940 Aubevoye

Country

France

Phone

+ 33 32773077

View All Listings by this Company