'Pexylene 50937 Natural, Black & Blue'. Rotationally moulded polyethylene materials available in natural (appears off-white), black & blue colours. For use with water up to 65°C.
'8108658 V0010_K LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
'8108658 V0010_V LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
FORTRON® natural (appears cream) or black coloured, injection moulded PPS materials. For use with water up to 85°C. Grades manufactured in Celanese Florence, USA: FORTRON® 1140L4 SF3001 NATURAL FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140L4 BLACK SD3002). FORTRON® 1140L6 SD3002 BLACK DW (formerly known as FORTRON® 1140L6 BLACK SD3002). FORTRON® 1140L6 SF3001 NATURAL FORTRON® 4184L6 SF3001 NATURAL FORTRON® 4184L6 SD3002 BLACK DW (formerly known as FORTRON® 4184L6 BLACK SD3002). Grades manufactured in Celanese Nanjing: FORTRON® 1140L4 SF3001 NATURAL DW (formerly known as FORTRON® 1140 L4 SF3001 natur CN). FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140 L4 SD 3002 black).
'Inoflon M 695'. White coloured (opaque), sintered PTFE material. For use with water up to 85°C.
'E 71 65 003'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.5mm. For use with water up to 85°C.
'EPDM70(E7-512K)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'FDJ-75'. Black coloured, injection moulded FKM rubber material. Shore hardness 76. Tested in-radius size 1.03mm. For use with water up to 85°C.
'NBR N65WKZ'. Black coloured, injection moulded NBR rubber material. Shore hardness 59. Tested in-radius 1.0mm. For use with water up to 23°C.
'N65WKZ'. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'NE7130 Grey 60'. Light grey coloured, injection moulded silicone rubber material. Shore hardness 60. Tested in-radius size 1.97mm. For use with water up to 85°C.
'Loctite 403'. Clear, liquid cyanoacrylate adhesive. Apply as per manufacturer's technical data sheet reference ‘2.6’, dated August 2012. Cure for 72 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TruTite™ 313 Thread Lock'. Blue coloured pipe sealant. Apply as per manufacturer's TDS version '1.0 26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CORE®'. Blue coloured pipe sealant. Apply as per manufacturer's instructions version '1', issue date '26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed), electronically operated tap assembly. The flow is controlled by a solenoid valve and activated via an infra-red sensor. Inlets are supplied with check valves (verified by test - suitable for backflow protection against fluid category 2). Maximum working pressure 6 bar. Maximum operating temperature 40 °C
Range of deck mounted, Infra-red electronic basin mixers with mixing device and adjustable temperature limiter. The tap incorporates EPDM O-rings. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a stainless-steel strainer prior to the solenoid. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Page 267 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
