Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.3 bar. Maximum operating temperature 60°C.

Section:

2411 Disinfection Equipment

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

CalUltra, model, WRAS and serial number on adhesive label on body.

Installation Requirements:

R001 R150 R170

Expiry date:

31/05/2029

Model:

Single Lamp UV Disinfection Units: CalUltra 132 - 1½” NPT (M). CalUltra 220 - 2” NPT (M). CalUltra 332 - 2” NPT (M). Double Lamp UV Disinfection Units: CalUltra 416 - 2½” NPT (M). CalUltra 530 - 3” NPT (M). CalUltra 662 - 4” NPT (M). Disinfection Equipment X denotes a UV sensor or a glow plug and is replaced with: 5= Glow Plug & 6 = UV Sensor. X denotes the type of power cord and is replaced with: 1 = NEMA 5/15. 2 = CEE 7/7. 3 = BS1363. 4 = AS/NZ 3112. 5 = NEMA 6/15. Additional Suffixes can be used for different lamps or sensor calibrations: HW, TOC or 50.

Approval Holder:

Calmag Yorkshire Limited

Company Name

Calmag Yorkshire Limited

Address

Riverview Buildings Bradford Road Riddlesden Keighley

Postcode

BD20 5JH

Country

United Kingdom

General Email

sales@calmagltd.com

View All Listings by this Company

'KOCETAL K300, K500 & K700'. Off-white coloured (opaque), injection moulded acetal materials. For use with water up to 85°C.

Section:

5015 Acetal

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

240655037

Expiry date:

30/06/2029

Approval Holder:

KOLON ENP, Inc.

Company Name

KOLON ENP, Inc.

Address

[39537] 64 Gongdan 3-gil, Gimcheon-si, Gyeongsangbuk-do

Country

Korea, Republic of

View All Listings by this Company

'Magnum 8391 UV White TM8302386'. White coloured, injection moulded ABS material. For use with water up to 85°C.

Section:

5020 Acrylonitrile Butadeine Styrene Copolymer (ABS)

Expiry date:

31/08/2029

Approval Holder:

Resinex UK Ltd.

Company Name

Resinex UK Ltd.

Address

11 The Valley Centre, Gordon Road High Wycombe, Buckinghamshire

Postcode

HP13 6EQ

Country

Bucks.

Phone

+44 (0) 1494 459 881

General Email

info@resinex.co.uk

View All Listings by this Company

'BPL High Build QD Bitu Black'. Factory applied, black coloured bituminous coating. Apply as per manufacturer’s data sheet ‘427-rev03’ dated 'Feb' 2024'. Cure: flash off for 15 minutes at ambient temperature of 30°C, followed by stoving at 55°C for 10 minutes and then 7 days maturation at ambient temperature of 30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5021 Bituminous Based Products

Section Subtitle:

Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials containing petroleum or asphaltic bitumen are not approved for use on water-retaining structures with large surface:volume ratio such as lining of pipes, cisterns or water storage tanks in contact with wholesome water, but may be acceptable for use where there is only a small surface area in contact with the water – e.g. taps, valves and pipe connectors.

WRAS Approval Number:

240955013

Expiry date:

30/09/2029

Approval Holder:

Berger Paints India Limited

Company Name

Berger Paints India Limited

Address

14 & 15 Swarnamoyee Road, Howrah - 711103, West Bengal

Country

India

View All Listings by this Company

'SMS EPX-02 Solvent Free Epoxy Coating and Hardener'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix coating & hardener in a 3.5:1 volume ratio and apply as per manufacturer's painting instructions 'Document Code 30', 'Rev No 7', dated '01.09.2018'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

240555049

Expiry date:

31/05/2029

Approval Holder:

SAMSUN MAKINA SANAYI A.S.

Company Name

SAMSUN MAKINA SANAYI A.S.

Address

ORGANIZE SANAYI BOLGESI, YASAR DOGU CADDESI, N0:41 55300, KUTLUKENT, SAMSUN

Country

Turkey

Phone

+90 362 266 51 60

General Email

info@samsunmakina.com.tr

View All Listings by this Company