'Vydyne A30 GF Natural WR'. Natural (light grey coloured), injection moulded PA66 material. For use with water up to 85°C.
‘PLUSTEK PAT7001G50BK11’. Black coloured, extruded polyamide material. For use with water up to 85°C.
'Maincor MLC Pipe'. Triple layered, extruded PERT/Al/PERT pipe consisting of a white coloured inner layer, grey coloured middle layer and a white coloured outer layer. For use with water up to 85°C.
'Icorene 1613 BK85 DW Black'. Black coloured, rotomoulded LLDPE material. For use with water up to 85°C.
'Asrene SP4808'. White coloured, compression moulded HDPE material. For use with water up to 65°C.
'NORYL FE1410PW – 73701, NORYL FE1520PW – 73701, NORYL FE1630PW – 73701 & NORYL FE1740PW – 73701'. Black coloured, injection moulded PPE + PS materials. For use with water up to 85°C.
'NORYL WM330G-73701'. Black coloured, injection moulded PPE + PS material. For use with water up to 85°C.
'NORYL FE1410PW - 801' (appears yellow-cream coloured) & 'NORYL FE1410PW - 960' (light-grey coloured). Injection moulded PPE & PS materials. For use with water up to 85°C.
XYRON™ WG725 AWY2139 (off-white). XYRON™ WG725 AWY6633 (beige). XYRON™ WG725 AWY3328 (black) XYRON™ WG735 AWY3327 (black) XYRON™ WG735 AWY2138 (grey). XYRON™ WG735 AWY2272 (grey) XYRON™ WG735 AWY6632 (beige). Injection moulded, Modified Polyphenylene Ether materials. For use with water up to 85°C.
'RAMTON PPS300PWG8NT'. Brown coloured, extruded PPS material. For use with water up to 85°C.
‘Coprax® PP-R Pipe’. Blue coloured (with green stripe), extruded PP-R pipe. For use with water up to 85°C.
‘Coprax® PP-R Fitting’. Blue coloured, injection moulded PP-R fitting. For use with water up to 85°C.
‘RAMLLOY PNS300PWG6BK10’. Clear, extruded polystyrene polyphenylene material. For use with water up to 85°C.
'Xarec WA212, WA210 & WA552'. Injection moulded, glass fibre reinforced, syndiotactic polystyrene sheet materials which are available in natural (appears cream) or black. For use with water up to 85°C.
'DETAI'. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'POLYFLON PTFE HP001'. White coloured, compression moulded PTFE material. For use with water up to 85°C.
'Stronghold SH-EP1'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions version '01', dated 'Jan 2024'. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TCM100'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions ref. no. 'rev5' dated 07.03.2024. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP70-S3150/B1-73898 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. For use with water up to 85°C.
'EPDM 5518 Seal 3G'. Black coloured, compression moulded, EPDM rubber seal. Shore hardness 58. Tested in-radius size 1.92mm. For use with water up to 23°C.
Page 242 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
