Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Welmortar-III'. Factory applied, grey coloured cement mortar. Mix cement, sand and water in a mass ratio of 2:3:0.85. Apply as per manufacturer's Standard Operating Procedure 'WDIPL/QA/WI/14A', revision '0', dated '01.10.2021'. Cure for 21 days at 30°C & 70% humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Corro Coat EP-F 5001'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer's technical data sheet dated '24 September 2021'. Cure for 2.5 minutes@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 Red & Pentaline 1000 Grey'. Factory applied, red and grey coloured, two component solventless epoxy coatings. Mix component A & B in a volume ratio of 3:1 and apply as per manufacturer's document number 'Chembur R&D/PI/05', issue date '03/04/2023'. Cure for 7 days@30°C. 'Pentaline 1000 Red' is for use with water up to 45°C. 'Pentaline 1000 Grey' is for use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WB50 Black Waterborne Pipe Anticorrosive Paint'. Factory applied, black coloured polyacrylate coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WEP50 Black Waterborne Epoxy Pipe Anticorrosive Paint'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'3011 Red Epoxy Anticorrosive Coating'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's instructions '004', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5015 Blue Epoxy Anticorrosive Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘E1H8691 ValveClad, E1H8868 ValveClad & E2H6531’. Factory applied, blue coloured epoxy powder coatings (manufactured in UK and France). Apply as per manufacturer’s instructions dated January 2023. Cure for 10 minutes@180°C (metal temperature). E1H8691 ValveClad and E1H8868 ValveClad are for use with water up to 23°C. E2H6531 is for use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 Blue Waterborne Pipe Anti-Corrosive Paint'. Factory applied, blue coloured polyacrylate paint. Apply as per manufacturer's TDS/IFU '001', 'First Edition', dated '2021.12.12'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NP-TANK 500 PW'. Factory applied, white coloured (once mixed), two-component, solvent-free epoxy coating. Mix Part A (white liquid) with Part B (dark amber liquid) in a 3:1 volume ratio. Apply as per manufacturer's TDS 'Rev. 06/22'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 25 of 51
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
