‘Tecotek OP20 BK014 01 0A QF, Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF’. Tecotek OP20 BK014 01 0A QF is a black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C. Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF are black coloured, injection moulded, filled PPO/HIPS materials suitable for use with water up to 85°C.
‘4TECH 9S20000 W-A-ABK 01 0A QF, 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK’. Black coloured, injection moulded PPO & PPO/HIPS materials. 4TECH 9S20000 W-A-ABK 01 0A QF is an unfilled PPO material suitable for use with water up to 23°C. 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK are filled PPO/HIPS materials suitable for use with water up to 85°C.
'BORplus Faser Composite Stabil PP-RCT Pipe'. Extruded, multi-layered PP-RCT pipe comprising of a grey coloured inner layer, black coloured middle layer and grey coloured outer layer. For use with water up to 85°C.
'5308400500 polypropylene liner tube', taupe coloured, injection moulded polypropylene liner. In March 2025, '5308400500 polypropylene liner tube', natural (appears beige), injection moulded polypropylene liner was added to the approval. For use with water up to 23°C.
'Trutite PTFE Tape'. White coloured (semi-translucent), extruded PTFE tape. For use with water up to 85°C.
'J-FIX ULTRA-BOND 100 EPOXY RESIN'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions 'Re00', dated 'August 2023'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPDM 5070 Membrane'. Black coloured, compression moulded EPDM membrane. Shore hardness 58. Tested in-radius size 1.02mm. For use with water up to 85°C.
'EP703901 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. For use with water up to 85°C.
'ERIKS 559706'. Black coloured, EPDM 'O' ring with a vulcanised joint, manufactured by extrusion. Shore hardness 70 ShA. Tested in-radius size 8.0mm. For use with water up to 23°C.
'EPDM-A-001'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'TT-001 Natural'. Natural (appears white, translucent), compression moulded silicone rubber material. Shore hardness 50. Tested in-radius size 0.5mm. For use with water up to 85°C.
'Guarri 543'. Blue coloured pipe sealant. Apply as per manufacturer's instructions '543 Usage', version '0', issue date '22/06/2023'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Superpower SOS 3 in 1 (SP2)'. Green coloured (translucent) anaerobic adhesive. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Loctite 638'. Green coloured anaerobic adhesive. For use with water up to 23°C. This product is to be applied and cured in strict accordance with the manufacturer’s instructions.
‘THERMOLAST DW’ range of natural (appears off-white), black, white & grey coloured, extruded TPE-S materials with an in-radius between 0.39mm & 0.41mm. DW7HTV-(1) (70 ShA). DW7HTU-(1) (75 ShA). DW8HTV-(1) (80 ShA). DW8HTU-(1) (85 ShA). DW9HTV-(1) (90 ShA). DW0HTV-(1) (40 ShD). (1) – indicates the colour of the material: - LCNT: means without pigment (natural colour). - 9017: means black coloured material. - 9003: means white coloured material. - 7---: 4 digit code means grey coloured material, mixture of white and black pigments. For use with water up to 65°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a ‘Type AB’ air gap arrangement (verified by test, suitable for backflow prevention against Fluid Category 5). Maximum working pressure 7.5 bar. Cold water supply only.
Range of wall mounted, single hole, single outlet (fixed) electronically operated tap assemblies incorporating stainless-steel bodies (various finishes - see model). Flow is controlled via solenoid valve and actuated by a capacitive (TSL-881/883) or infra-red (TSL-882/884) sensor. The products can also be supplied with an additional plastic aerator (from a choice of two). Maximum working pressure 7.5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, (fixed), electronically controlled combination tap assemblies (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar. Maximum operating temperature 70.0°C.
Range of spring-loaded resilient trim in-line check valve cartridges with acetal bodies. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ¼ turn ceramic disc headworks with brass bodies, EPDM ‘O’-rings and either a red or blue silicone gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Page 235 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
