Two-way ceramic disc diverter headwork (2 on, 1 off) with a plastic body and silicone seals. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘D-TECH DTCAPOL-300’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions dated 29.01.2021. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPIT ViPer XTREM'. grey coloured (once mixed), two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'VIPER XTREM | 2023-1'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RAMSET ChemSet 801 Xtrem XC²'. Grey coloured coloured, two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'August 15, 2018'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Floor standing, single hole, single outlet (fixed) combination tap assemblies (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates manual diverter to a shower outlet. The spout outlet incorporates an open outlet type spout. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve actuated via an infra-red sensor. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlets incorporate approved check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection and stainless-steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 215 of 279
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
