'SRC GRE Pipe'. Yellow coloured (opaque), SRC GRE pipe manufactured by dual helical filament winding. For use with water up to 70°C.
'Extrabrite'. Light brown coloured GRE pipe manufactured by filament winding (at Extra Co Fibre Glass & Prefab Houses LLC – Sharjah, UAE and Extra Co Industries LLC – Ras Al Khaimah, UAE). For use with water up to 60°C.
'Extrabrite'. Light brown coloured GRE fittings manufactured by filament winding (at Extra Co Fibre Glass & Prefab Houses LLC – Sharjah, UAE) or hand lay-up (at Extra Co Industries LLC – Ras Al Khaimah, UAE). For use with water up to 60°C.
'SURU Lubricant'. Yellow coloured lubricant. Apply as per manufacturer's instructions dated '18th Feb 2015'. For use with water up to 60°C.
'EPLAMID 66 GFS 30 FW NC'. Natural (appears beige), injection moulded, glass fibre reinforced PA66 material. For use with water up to 85°C.
'EPLAMID 66 GFS 30 FW BK'. Black coloured, injection moulded, glass reinforced PA66 material. For use with water up to 85°C.
‘RADISTRONG® AROMA RV400RKC2 106 NT, RV500RKC2 106 NT & RV600RKC2 106 NT’. ‘RADISTRONG® AROMA RV400RKC2 306 BK, RV500RKC2 306 BK & RV600RKC2 306 BK’. ‘RADISTRONG® AROMA RV300RKC2 106 NT’ & ‘RADISTRONG® AROMA RV300RKC2 306 BK’ were added to the approval in February 2024. Natural (indicated by NT - appear cream in colour) and black coloured (indicated by BK), injection moulded, glass fibre filled (between 30% & 60%), PA66 materials. For use with water up to 85°C.
'EUREXPOL PI6808C'. Yellow coloured, isophthalic unsaturated polyester resin material made by mixing and pouring into a mould. For use with water up to 23°C.
'SLA Barrier Pipe' (formerly known as ‘Egeplast SLA Pipe’). Extruded, triple layered pipe consisting of an black coloured PE 100 inner layer, aluminium middle layer and blue coloured (with brown coloured longitudinal stripe) PE 100 outer later. For use with water up to 23°C.
‘Palaplast Hydropal W PE80 & PE100 pipes’. Extruded, PE80 & PE100 pipes, both available in either blue colour or black colour (with blue stripe). All pipes are for use with water up to 23°C.
‘Polypipe Black PE100 & Blue PE100 Pipes’. Black or blue coloured, extruded PE100 pipes. For use with water up to 23°C.
'Aquaflex PE-80'. Blue coloured, extruded HDPE pipe. For use with water up to 23°C.
'PPE-2211 GF30 SAWyy-Gxxxx' (where yy-Gxxxx indicates and is replaced with a combination of numbers and letters). Off-white coloured, injection moulded PPE material. For use with water up to 85°C.
'Q-Therm'. Green coloured, extruded PP-R 80 pipes. For use with water up to 85°C.
'TFM1700'. White coloured, injection moulded PTFE ring. For use with water up to 85°C.
'Titan A202'. Site applied, pale yellow coloured hydrophilic polyurethane foam. Apply as per manufacturer's Tech Sheet '03', dated '10.01.2023' and spray treated surface with water. Cure for 6 hours at an ambient temperature (19-21°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CHEMILINE AF 023 FB 170'. Black coloured CR & SBR rubber material which has been calendared and then cured in an autoclave. Shore hardness 55. Tested in-radius size 1.05mm. For use with water up to 23°C.
‘Sunaflex T 9635’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'A-KT 80-00'. Black coloured, extruded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.1mm. Between April 2023 and May 2025, the material was for use with water up to 23°C. Between June 2025 and April 2028, the material is for use with 85°C.
'A-KT 90-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 90. Tested in-radius size 1.0mm. Between April 2023 and October 2024, the material is for use with water up to 23°C. From November 2024, the material is for use with water up to 85°C.
Page 209 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
