'GTH-CC Iron Red'. Factory applied, two-component, red coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GTH-CC Ice Grey'. Factory applied, two-component, white coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lacaze Radiant'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RC851'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Tianbao SS Epoxy Coating'. Factory applied, two-component white coloured epoxy coating. Mix component 1 and component 2 in a mass ratio of 6:1 and apply as per manufacturer's operation in instructions 'Tianbao SS', 'version 1.0' issued on '06/02/2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Kejriwal OPC’. Factory applied, grey coloured in-organic, Ordinary Portland Cement mortar. Mix cement, sand & water in a mass ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux QD Exterior Coating'. Factory applied, blue coloured, two-component epoxy coating comprising of a base and accelerator. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet '679', dated 'Jun 2020'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vinoleo ME'. Amber coloured lubricant to be applied as per manufacturer's instructions '163771', dated April 2016. For use with water up to 60°C.
'RADILON® A RV300RKC 306 BK' (black coloured). In December 2022, 'RADILON A RV300RKC 106 NT' (natural, appears off-white) was added to the approval. Injection moulded PA66-GF30 materials. For use with water up to 85°C.
‘Ultramid® A3EG10 FC Aqua Black 23285’. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
Page 206 of 854
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
