'IROGRAN® A 85 P 4441 FCM'. White coloured, injection moulded polyurethane material. For use with water up to 60°C.
'IROGRAN® A 85 P 4394 FCM'. Clear (colourless), injection moulded polyurethane material. For use with water up to 60°C.
‘D-TECH DTCAPOL-300’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions dated 29.01.2021. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'D-TECH DTCAVYN-300'. 'D-TECH DTCAVYN-420' was added to the approval in July 2024. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resins. Apply as per manufacturer's instructions dated 01.07.2024. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XB/300'. Black coloured, compression moulded butyl (IIR) material. Shore hardness 58 ShA. Tested in-radius size 1.24mm. For use with water up to 23°C.
'9710 'O' Rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radius size between 0.5mm & 3.4mm. For use with water up to 85°C.
Initial approval was for ‘SMS-80’ (shore hardness 80) only. In April 2024 ‘SMS-50' (shore hardness 50) & ‘SMS-70’(shore hardness 70) were added to the approval. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AEC 2/EPDM-50, AEC 3/EPDM-60, AEC 4/EPDM-70 & AEC.A5/EPDM-80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EDXX 74'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.5mm. For use with water up to 85°C.
'6741'. Brown coloured, compression moulded FKM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 85°C.
'TH5/01/4 BLK Diaphragm Seal'. Black coloured, injection moulded HNBR diaphragm seal. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'PLIMAT ABS PRESSURE Solvent Cement'. Grey coloured solvent cement intended to join ABS pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BOSS PRESSURE ABS Solvent Cement'. Grey coloured solvent cement intended to join ABS pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DURAPIPE One Step ABS Solvent Cement'. Grey coloured solvent cement intended to join ABS pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EFFAST ABS PRESSURE Solvent Cement'. Grey coloured solvent cement intended to join ABS pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BOSS PRESSURE PVC Solvent Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DURAPIPE RH PVC-U Solvent Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RIAMAXX HR XE4349 KTW natur. RIAMAXX HR XE4349 KTW schwarz. RIAMAXX HR XE4350 KTW natur. RIAMAXX HR XE4350 KTW schwarz. RIAMAXX HR XE4351 KTW natur. RIAMAXX HR XE4351 KTW schwarz. RIAMAXX HR XE4352 KTW natur. RIAMAXX HR XE4352 KTW schwarz'. Natural (appears beige) and black coloured, injection moulded Polyketone materials. For use with water up to 85°C.
'RIAMAXX HR GF40 Xgea14 KTW schwarz'. Black coloured, injection moulded Polyketone material. For use with water up to 85°C.
Wall mounted electric heater, incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Page 182 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
