'Welmortar-III'. Factory applied, grey coloured cement mortar. Mix cement, sand and water in a mass ratio of 2:3:0.85. Apply as per manufacturer's Standard Operating Procedure 'WDIPL/QA/WI/14A', revision '0', dated '01.10.2021'. Cure for 21 days at 30°C & 70% humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Corro Coat EP-F 5001'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer's technical data sheet dated '24 September 2021'. Cure for 2.5 minutes@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 Red & Pentaline 1000 Grey'. Factory applied, red and grey coloured, two component solventless epoxy coatings. Mix component A & B in a volume ratio of 3:1 and apply as per manufacturer's document number 'Chembur R&D/PI/05', issue date '03/04/2023'. Cure for 7 days@30°C. 'Pentaline 1000 Red' is for use with water up to 45°C. 'Pentaline 1000 Grey' is for use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WB50 Black Waterborne Pipe Anticorrosive Paint'. Factory applied, black coloured polyacrylate coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WEP50 Black Waterborne Epoxy Pipe Anticorrosive Paint'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'3011 Red Epoxy Anticorrosive Coating'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's instructions '004', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5015 Blue Epoxy Anticorrosive Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 Blue Waterborne Pipe Anti-Corrosive Paint'. Factory applied, blue coloured polyacrylate paint. Apply as per manufacturer's TDS/IFU '001', 'First Edition', dated '2021.12.12'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AMMT-029 Waterborne Anticorrosive Coating'. Factory applied, black coloured acrylic modified resin coating. Apply as per manufacturer's Instructions for Users 'version 2.00', updated '11/01/2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Xypex Concentrate'. Site applied, grey coloured, cementitious coating. Mix 'Xypex Concentrate' with water in a 5:2 ratio and apply as per manufacturer's datasheet 'DAT-CON-UK, REV-06-21'. Cure for 3 days@7°C in damp conditions, following by 18 days@7°C. Please note that 1 day cure = 24 hours. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 180 of 652
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
