'QY031E'. Factory applied, blue coloured epoxy powder coating. Pre-heat the substrate to 250°C and then apply the coating at a temperature of 160°C as per manufacturer's product specification 'QY031E-01' dated '2022-3-23'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lacaze Radiant'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RC851'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Kejriwal OPC’. Factory applied, grey coloured in-organic, Ordinary Portland Cement mortar. Mix cement, sand & water in a mass ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4841 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '4841/031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Krystaline Add PLUS 2.5'. Grey coloured, site-applied waterproofing admixture. Admixture is to be added to cement mix in a dosing ratio of 2.5 kg per m3 of concrete. Cure for 5°C for 48 hours. For use with water up to 23°C. This material is only approved for the dosing and curing conditions that appear on the approval. If the dosing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LATTYflon 4789'. Yellow coloured, braided fibre/PTFE gland packing. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'LATTYgraf EFA'. Grey coloured, graphite sheet material manufactured by calendaring. For use with water up to 85°C.
'SANIBIW WB-R Reinforced Multilayer Hoses' and ‘SANIBIW WB-R Hose’. 'SANIBIW WB-R Reinforced Multilayer Hoses' are dual layered, extruded hoses, consisting of an off-white translucent (natural) silicone rubber inner layer and VMQ silicone rubber (with PES reinforcement) outer layer. The outer layer is available in black, red/brown, white or silver colours. Shore hardness 70. The inner and outer layers each have a tested in-radius size of 1.1mm. ‘SANIBIW WB-R Hose’ is a single layered, translucent (natural), extruded silicone rubber hose with PES reinforcement. Shore hardness 70. Tested in-radius size of 2.0mm. All hoses are for use with water up to 85°C.
'SANIBIW WB Hose’. Single layered, uncoloured & translucent (natural), extruded silicone rubber hose. Shore hardness 70. Tested in-radius size of 2.0mm. For use with water up to 85°C.
Page 177 of 780
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
