'Tefzel® ETFE 200, 207, 280, 750, HT2181, HT2183 & HT2185'. Un-pigmented (white coloured), compression moulded ETFE material. For use with water up to 85°C.
'Teflon® FEP 100 X, 100-J, 106 X, CJ 95 X, CJ 99 X & 9302 X'. Un-pigmented (white coloured, compression moulded FEP material. For use with water up to 85°C.
''Teflon® PFA 340 X, 345 X, 350 X, 350-T-J, 440 HP X, 445 HP X, 450 HP X & 416 HP X'. Unpigmented (white coloured), compression moulded PFA materials. For use with water up to 85°C.
'TFM1700'. White coloured, injection moulded PTFE ring. For use with water up to 85°C.
'Teflon® PTFE 640XT X, 807N X, NXT 70, NXT 75, 6CN X, 62 X, 62N X, 62XT X, 669N X, 669 X, NXT 85, 605XT X, 6C X, 7A X, 641XT X & 650XT X’. White coloured, extruded or compression moulded PTFE material. For use with water up to 85°C.
'ERIKS 55950 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 3.5mm. For use with water up to 85°C.
‘Sunaflex T 9635’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'A-KT 80-00'. Black coloured, extruded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.1mm. Between April 2023 and May 2025, the material was for use with water up to 23°C. Between June 2025 and April 2028, the material is for use with 85°C.
'A-KT 90-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 90. Tested in-radius size 1.0mm. Between April 2023 and October 2024, the material is for use with water up to 23°C. From November 2024, the material is for use with water up to 85°C.
‘CRIEP50 & CRIEP80’. Black coloured, compression moulded EPDM rubber materials. Shore hardness 50 & 80 respectively. Tested in-radius size 1.0mm. For use with water up to 70°C.
‘N5118F, N5518F, N6118F, N6518F, N7118F, N7008F, N7518F, N8118F, N8518F & N9118F’. Black coloured, compression moulded NBR rubber `O` rings and gaskets. Shore hardness between 50 & 90. 'O' rings have a tested in-radius size of between 0.25mm & 5.0 mm. Gaskets have a tested in-radius size of between 0.3mm & 7.5mm. For use with water up to 85°C.
'0612 HNBR'. Yellow coloured (opaque), injection moulded HNBR 'O' rings. Shore hardness 70. Tested in-radius size 1.31mm. For use with water up to 85°C.
‘KSIL70’. Natural (off-white coloured), silicone rubber gaskets manufactured by pulltrusion. Shore hardness 70. Tested in-radii sizes between 0.55mm & 0.85mm. For use with water up to 85°C.
‘2061 VMQ 60’, red coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 60. ‘2172 VMQ 70’, blue coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 70. O-rings have a tested in-radius of 2.0mm Washers have a tested in-radius of 2.5mm. Lip seals have a tested in-radius of 0.45mm For use with water up to 85°C.
‘SIL4008F, SIL4008F (N), SIL4008F (H), SIL4008F (R) & SIL4008F (BK). SIL4508F. SIL5008F, SIL5008F (H), SIL5008F (R) SIL5008F (BK), SIL5008F (B). SIL5508F. SIL6008F, SIL6008F (N), SIL6008F (H), SIL6008F (R), SIL6008F (BK). SIL6508F. S7008F, S7008F (N), S7008F (H), S7008F (R), S7008F (BK), SIL7118F, SIL7018F. SIL7508F. SIL8008F, SIL8008F (N), SIL8008F (H), SIL8008F (R), SIL8008F (BK)’. Range of compression moulded, silicone rubber `O` rings and gaskets available in natural, white, grey, blue, red, pale yellow, orange, green, brown and black colours. Shore hardness range 40 - 80. ‘O’ rings have an in-radius size range of 0.2mm – 5.0mm. Gaskets have an in-radius size range of 0.3mm – 7.5mm. For use with water up to 85°C.
'EMS Force 5543'. 'EMS Force 5543-P' was added to the approval in February 2025. Blue coloured pipe sealants. Apply as per manufacturer's instructions 'TLM.LB.07', version '0', issue date '07/03/2016'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'THAT RAPID BLU-STUFF'. 'THAT RAPID BLU-GEL' was added to the approval in February 2025. Blue coloured pipe sealants. Apply as per manufacturer's instructions 'TLM.LB.07', version '0', issue date '18/05/2023'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Zilan DW-HT Rubber Membrane'. Black coloured, compression moulded butyl rubber membrane (in the form of a sheet of rubber). Shore hardness 50 ShA. Tested in-radius size 1.0mm. For use with water up to 85°C.
3-in1 single hole, single outlet (swivel) combination tap assembly (chromium plated or brushed stainless steel PVD brass). The cold//hot/mixed water circuit incorporates a ceramic cartridge headwork with a single lever operating member. The near boiling water circuit incorporates a quarter turn ceramic disc headwork with a single lever operating member. The tap is supplied with a stainless steel braided PEX lined flexible hose assembly, brass adaptor incorporating a plastic flow regulator, NBR washer and plastic adaptor to connect the tap to the near boiling water unit (not supplied) and a PTFE or silicone (from September 2024) flexible pipe to deliver near boiling water back to the tap. The spout outlet incorporates a plastic aerator, which includes a central stainless steel tube insert throughout the near boiling water outlet of the aerator. Maximum working pressure 10.0 bar. Maximum operating temperatures: 65°C (cold/hot/mixed water circuit). 99°C (near boiling water circuit after boiler unit, cold supply only prior to boiler unit).
Range of single hole, single outlet, electronically controlled tap assemblies (brass body – various finishes). The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Models xxx.yyy.170E/W are supplied with a click clack waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 171 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
