A range of variable speed booster pumps with stainless steel bodies and impeller. Maximum working pressure: 8 bar. Maximum operating temperature: 35°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250708701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1” BSP (F) x 1” BSP (F).

Marking:

Calpeda and logo on adhesive label located on the pump’s inverter cover.

Installation Requirements:

R001 R415

Expiry date:

31/07/2030

Model:

MÈTA - Single pump variable speed pressure boosting system with integrated control, 1.35kW, nominal speed n=4500rpm, IPX4. MÈTA SMALL - Single pump variable speed pressure boosting system with integrated control, 0.65kW, nominal speed n=5800rpm, IPX4. MÈTA-2 - Single pump variable speed pressure boosting system with integrated control, 1kW, nominal speed n=5800rpm, IPX4.

Product Images

Approval Holder:

Calpeda S.p.A

Company Name

Calpeda S.p.A

Address

Via Roggia Di Mezzo 39 36050 Montoro Vicentino Vicenza

Country

Italy

View All Listings by this Company

Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (MS(s) models), 4.0 bar (AM(E) models) Maximum operating temperature 85°C

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241102725

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

TERAL, model, size & technical information on date label on body. Flow arrow on cover.

Installation Requirements:

R001 R415

Expiry date:

30/11/2029

Model:

MS(m)XXX-XX-E 1.m: different phase. --m: single phase, none: three phases 2.XXX: Rated flow (L/min) 3.XX: Rated power(kW). 4.E: E type end connection mode and size -- Rated flow(70-120m3/h): G1¼"XG1" -- Rated flow(210m3/h): G1½"XG1¼" -- Rated flow (370 m3/h): G2"XG1¼ AM(E) XXxXX (B) X/X-X XX(S) 1. E: Intelligent Type 2. XX: Inlet diameter (mm), range: 25,32,40,50 mm. 3. XX: Outlet diameter (mm), range: 25,32,40,50 mm. 4. B: alternative pump group 4. X/X: number of impeller /number of smaller impeller (if any) 5. X: motor frequency 6. XX: Rated power(kW) 7. S: different phase (S: single phase, none: three phases.)

Manufacturer:

Teral Asia Ltd

Company Name

Teral Asia Ltd

Address

Room 1001 10/F, Olympia Plaza, 255 Kings Road, North Point

Country

Hong Kong

View All Listings by this Company

Range of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2204372

Size:

1” BSP (F)

Marking:

SFA Logo, Saniboost Smart, model number other technical information on adhesive label on body.

Installation Requirements:

R001 R415

Expiry date:

30/04/2027

Model:

Saniboost Smart Intelligent Water Booster Pump.

Product Images

Approval Holder:

SFA Saniflo UK Ltd

Company Name

SFA Saniflo UK Ltd

Address

Unit 1 Watford Interchange Colonial Way Watford

Postcode

WD24 4WP

Country

United Kingdom

Phone

020 8842 0033

General Email

Graham.davies@sfasaniflo.co.uk

View All Listings by this Company

Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250902720

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN25 - DN200 flanged.

Marking:

Dooch, model, serial number and technical info on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

30/09/2030

Proviso:

The discharge from the drain core must be made via a type AA, AB or AD air gap, or in accordance with EN 1717.

Model:

XRLNa-b-c-d Where: XRL = model. With N = Wetted metallic material in SUS316L, Without N = Wetted metallic material in SUS304. a = Rated flow in m³/h (1 – 255). DN25 = 1-3. DN32 = 4-5. DN40 = 10. DN50 = 15-20. DN65 = 32. DN80 = 45. DN100 = 64 or 95. DN150 = 125-155. DN200 = 185-255. b = Number of impellers (stages 1 – 36). DN25 & DN32 models with 1 – 36 stages. DN40 models with 1 – 22 stages. DN50 models with 1 – 17 stages. DN65 models with 1 – 14 stages. DN80 models with 1 – 13 stages. DN100 models with 1 – 8 stages. DN150 models with 1 – 10 stages. DN200 models with 1 – 8 stages. c = Number of cutting impellers (0 – 3). (Note: c can be omitted when c = 0.) d = DN size (DN25 – DN200). (Note: d can be omitted.) E.g., XRL32-7-2-DN65 denotes: Pump is made of SUS304, rated flow 32 m³/h, 7 impellers, 2 cutting impellers and size DN65.

Product Images

Approval Holder:

SHANGHAI SINO-KOREA DOOCH PUMP MFG. CO., LTD

Company Name

SHANGHAI SINO-KOREA DOOCH PUMP MFG. CO., LTD

Address

No 239 Zhangliantang Rd Liantang Ind Park Qingpu District Shanghai City China

View All Listings by this Company

Manufacturer:

ZHONGHAN DOOCH PUMP(HUZHOU)CO., LTD.

Company Name

ZHONGHAN DOOCH PUMP(HUZHOU)CO., LTD.

Address

NO 669 DAYANG ROAD KANGSHAN STREET HUZHOU ZHEJAING CHINA

View All Listings by this Company

Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250904702

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Wilo, made in Korea, Model No., Serial No., website address, & other tech info on data label. Wilo printed on control panel.

Installation Requirements:

R001 R415

Expiry date:

30/09/2030

Model:

PBI-L203EA - Suction 25A(1”) Discharge 25A(1”) PBI-L204EA - Suction 25A(1”) Discharge 25A(1”) PBI-L205EA - Suction 25A(1”) Discharge 25A(1”) PBI-L402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-L803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD203EA - Suction 25A(1”) Discharge 25A(1”) PBI-LD402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) 1 - Series PBI-L: Electronic Boosting Pump Variable Speed Pump(Inverter Pump). 2 - Number of Pumps None/blank : Single Type (One Pump), D: Duplex Type (Two Pumps). 3 - Rated Flow capacity 2 : 2㎥/hr, 4 : 4㎥/hr, 8 : 8㎥/hr. 4 - Number of Impellers 02 : 2 Impellers, 03 : 3 Impellers, 04 : 4 Impellers, 05 : 5 Impellers. 5 - Power 60Hz L: 110V ~, J: 120V ~ , 127V~, M: 220V~ D: 110V/220V~, I: 220/380V 3~, T: 220V 3~, U: 380V 3~, N: 440V 3~, R: 480V 3~. 50Hz Z: 110V ~, C: 120V ~, 127V~, E: 220V ~, F: 110V/220V ~, G: 220/380V 3~, H: 220V 3~, Q: 380V 3~, Y: 440V 3~. 6 - Automatic mode. None/blank : non automatic models A: models which equips themselves with components that are responsible for automatic mode.

Product Images

Approval Holder:

WILO Pumps Ltd.

Company Name

WILO Pumps Ltd.

Address

View All Listings by this Company

CM(E) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Maximum operating parameters: Cast iron models: Maximum working pressure 6.0 bar @ 90°C. Maximum working pressure 10.0 bar @ 40°C. Stainless steel models (not self-priming variants): Maximum working pressure 10.0 bar @ 99°C. Maximum working pressure 16.0 bar @ 90°C. Stainless steel self-priming models (CM(E) 1, 3 & 5 (AISI 304) only): Maximum working pressure 10.0 or 16.0 bar @ 60°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

251007701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1” - 2” BSP (F) or NPT (F) inlet and outlet.

Marking:

Grundfos and Grundfos logo, type, model, manufacturing country and technical information on adhesive labels either on the terminal box or fan cover. Grundfos and Grundfos logo on the terminal box or fan cover.

Installation Requirements:

R001 R415

Expiry date:

31/10/2030

Model:

CM(E)1, CM(E)3 and CM(E)5: CM(E)1, cast iron / AISI304 2 – 8 stages. CM(E)3, cast iron / AISI304 2 – 8 stages. CM(E)5, cast iron / AISI304 2 – 8 stages. CM(E)1, AISI316 2 - 14 stages. CM(E)3, AISI316 2 - 14 stages. CM(E)5, AISI316 2 - 13 stages. CM(E)10 CM(E)15 and CM(E)25: CM(E)10, cast iron / AISI304 1 – 5 stages. CM(E)15, cast iron / AISI304 1 – 4 stages. CM(E)25, cast iron / AISI304 1 – 4 stages. CM(E)10, AISI316 1 – 8 stages. CM(E)15, AISI316 1 – 4 stages. CM(E)25, AISI316 1 – 4 stages. Self-priming models: CM(E)1, AISI304 3 – 6 stages (S or O) CM(E)3, AISI304 3 – 6 stages (S or O) CM(E)5, AISI304 3 – 7 stages (S or O) Model key: CM/CME X1-X2 X3 X4-X5-X6-X7-X8 X9 X10 X11 X11-X12-X13-X14 Where: CM = Centrifugal Modular. CME = Centrifugal Modular with integrated frequency converter. X1 = Rated flow rate at 50 Hz (m³/h): 1-25. X2 = Number of impellers: 1-14. X3 = Pump Versions: A - Basic Version. E: Pumps with certificates/approvals. O: Self-priming version (maximum suction lift 8 metres) (Only available on CM(E) 1, 3 & 5 stainless steel (AISI304) models). S: Self-priming version (maximum suction lift 4 metres) (Only available on CM(E) 1, 3 & 5 stainless steel (AISI304) models). X4 = Pipe connection: R: Rp (ISO 7/1). S: Internal NPT thread. X5 = Material in contact with pump media: A: inlets and outlets parts EN-GJL-200, Pump shaft + Impellers and chambers EN 1.4301/AISI 304. G: Sleeve, Pump shaft + Impellers and chambers EN 1.4401/AISI 316. I: Sleeve, Pump shaft + Impellers and chambers EN 1.4301/AISI 304. X6 = Rubber parts in pump (excluding neck ring and shaft seal): E: EPDM. V: FKM. X7 = Shaft seal: A: O-ring seal with fixed driver. X8 = Material of rotating seal face: Q: Silicon Carbide (SIC). X9 = Material of stationary seal face: Q: Silicon Carbide (SIC). X10 =Material of secondary seal: E: EPDM. V: FKM. X11 = Supply voltage (electrical characteristics - not relevant for the WRAS approval): A/B/B1/B2/C1/E/E1/F/G/H/J/O/S/T/U/V/X. X12 = Motor information(electrical characteristics - not relevant for the WRAS approval): A/B/C/D/EF/G/H/I/J. X13 = Mains plug (electrical characteristics - not relevant for the WRAS approval): A/B/C/D. X14 = Sensor (electrical characteristics - not relevant for the WRAS approval): N: No sensor. Example: CM 10-3 A-R-I-E-A Q Q E C1-A-A-N

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company