3M™ Dyneon™ Fluoroplastic grades PFA 6502NZ, PFA 6502TZ, PFA 6505TZ, PFA 6515NZ, PFA 6515TZ, and PFA 6525TZ. White coloured (natural), transfer moulded PFA material. For use with water up to 85°C.
'PTFE G500 Ring/Seat'. White coloured, extruded PTFE ring/seat component. For use with water up to 85°C.
'PTFE G405'. White coloured, extruded, PTFE ring. For use with water up to 85°C.
'F1520'. Blue-grey coloured PTFE material manufactured by ram extrusion. For use with water up to 85°C.
3M™ Dyneon™ TF 1620, TF 1641, TF 1645, TF 1702, TF 1750, TFM 1600, TFM 1635, TFM 1700, TFM 1705, TF 4103K, TF 4105K, and TFM 4105K. White coloured, pressed+sintered PTFE materials. 3M™ Dyneon™ TF 2021Z, TF 2025Z, TF 2029Z, TF 2035Z, TF 2053Z, TF 2071Z, TF 2072Z, TF 2073Z, TFM 2001Z, TFM 2033Z and TFM 2070Z. White coloured, extruded PTFE materials. 3M™ Dyneon™ TF 4215 & TF 4303. Black coloured, pressed+sintered PTFE materials. For use with water up to 85°C.
'Art. 0985077200'. Black coloured, extruded silicone rubber tape. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'EPDM 70.10-02 'O'-rings & gaskets'. Black coloured, injection moulded, EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have a tested in-radius size of 0.5mm. The gaskets have a tested in-radii size between 0.5mm & 2.6mm. ‘O’ rings with a tested in-radius size of 2.6mm were added to the approval in May 2023. For use with water up to 85°C.
‘07096-80 gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 80. Tested in-radius size between 0.9mm & 1.75mm. For use with water up to 85°C.
'EP2480 BLK 'O' ring'. Black coloured, injection moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 1.31mm. For use with water up to 85°C.
'EPDM E282'. Black coloured, compression moulded EPDM sheet material. Shore hardness 80A. Tested in-radius size 1.0 For use with water up to 85°C.
'E7014F'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C. From April 2023, the material is for use with water up to 85°C.
'EPDM 70.503-00'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'51616 – E40, 51616 – E50, 51616 – E60, 51616 – E70 & 51616 – E80'. Black coloured, compression moulded EPDM materials. Shore hardness between 40 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'kSil PL60 Translucent'. Off-white coloured (translucent), silicone rubber material which is extruded onto the calendar. Shore hardness 60. Tested in-radius size 1.05mm. For use with water up to 85°C.
'FixCuivre'. Purple coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Loctite SI 5331 (known as 'Loctite 5331')'. White coloured silicone thread sealant. Apply as per manufacturers technical data sheet ‘reference 1.7’ dated May 2014. Cure for 96 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘M930F, M330F, M630F, M730F, M410F & M710F’. Beige coloured, injection moulded polyketone materials. For use with water up to 85°C.
Range of wall mounted electric showers (various finishes). The product incorporates a solenoid valve controlling the flow. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of inlet control valves with DZR brass bodies incorporating a pressure reducing valve (set at 1.5, 1.8. 2.0, 2.1, 3.0 or 3.5 depending on model) and a pressure relief valve (set at 3.0, 3.5, 4.5, 5.0. 6.0 or 8.0 depending on model. All models incorporate a stainless-steel mesh and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model CWIC355040 comes supplied with a tundish. For use with copper pipe to BS EN 1057, PB pipe (with inserts) to BS EN 7291-2:2010 and PEX pipe (with inserts) to BS EN 7291-3:2010. Maximum working pressure 16.0. Maximum operating temperature of 25°C.
Range of tundishes with plastic bodies. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Page 156 of 393
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
