'M-106'. Grey coloured, compression moulded mechanical carbon graphite cylindrical component. For use with water up to 85°C.

Section:

5022 Carbon

Expiry date:

30/11/2029

Approval Holder:

Metallized Carbon Corporation

Company Name

Metallized Carbon Corporation

Address

19 South Water Street, Ossining, NY 10562

Country

USA

View All Listings by this Company

'M-133'. Grey coloured, compression moulded mechanical carbon graphite cylindrical component. For use with water up to 85°C.

Section:

5022 Carbon

Expiry date:

30/11/2029

Approval Holder:

Metallized Carbon Corporation

Company Name

Metallized Carbon Corporation

Address

19 South Water Street, Ossining, NY 10562

Country

USA

View All Listings by this Company

‘NATZINC EP9015 SC PART A-BI.5431’ primer for use with ‘HYDRALFUN AC NOIR PAM -CZL8579’ finish/topcoat. Factory applied, black coloured (once mixed and applied), two-part epoxy primer for use with acrylic coating. Mix base & hardener of primer in a 100:10 weight ratio and apply one coat as per manufacturers TDS ‘NATZINC EP9010 BI 5431’, dated ‘February 2024’. No cure required. Apply one coat of the topcoat as per manufacturers TDS ‘HYDRALFUN AC NOIR PAM CZL8579’, dated ‘July 2018’ and cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

240855044

Expiry date:

31/08/2029

Approval Holder:

Prospa

Company Name

Prospa

Address

4, RUE DU 43ème R.I.C 80510 LONGPRE LES CORPS SAINTS

Country

France

View All Listings by this Company

'Hydroplate 1914'. Site applied, two-component, white coloured (once mixed and applied) Epoxy-polyamine coating. Mix parts A & B in a 3:1 weight ratio and apply as per manufacturer's Product Data Sheet 'B034', dated 'September 2024'. Cure coat 1 for 48 hours at 15°C. Cure coat 2 for 21 days at 15°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

240855045

Expiry date:

31/08/2029

Approval Holder:

Carboline Norge AS

Company Name

Carboline Norge AS

Address

Husebysletta 9, 3414, Lierstranda

Country

Norway

View All Listings by this Company

'PolySTH Pushfit Fittings'. Injection moulded, polybutylene pushfit fittings available in white and grey colours. For use with water up to 85°C.

Section:

5200 Polybutylene

Expiry date:

31/10/2029

Approval Holder:

Standard Hidráulica, S.A.U

Company Name

Standard Hidráulica, S.A.U

Address

Avda. Ferrería 73-75, 08110 Montcada i Reixac, Barcelona

Country

Spain

View All Listings by this Company