Range of M profile press fit fittings with a brass body and NBR O-rings, for use with copper pipe manufactured to EN1057 and stainless-steel pipe manufactured to EN10312. Maximum working pressure: 10 Bar. Maximum operating temperature: 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

240702016

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See Models.

Marking:

E logo and size on body.

Installation Requirements:

R001

Expiry date:

31/07/2029

Model:

Straight adaptor - Press fit x Female: 2PSFe1501 - 15MM x 1/2" (F) BSP, 2PSFe1502 - 15MM x 3/4" (F) BSP, 2PSFe2201 - 22MM x 1/2" (F) BSP, 2PSFe2202 - 22MM x 3/4" (F) BSP, 2PSFe2203 - 22MM x 1" (F) BSP, 2PSFe2802 - 28MM x 3/4" (F) BSP, 2PSFe2803 - 28MM x 1" (F) BSP, 2PSFe3503 - 35MMx 1" (F) BSP, 2PSFe3504 - 35MM X 11/4" (F) BSP, 2PSFe4205 - 42MM X 11/2" (F) BSP, 2PSFe5406 - 54MM X 2" (F) BSP. Straight adaptor - Press fit x Male: 2PSKe1501 - 15MM X 1/2" (M) BSP, 2PSKe1502 - 15MM X 3/4"(M) BSP, 2PSKe2201 - 22MM X 1/2" (M) BSP, 2PSKe2202 - 22MM X 3/4" (M) BSP, 2PSKe2203 - 22MM X 1" (M) BSP, 2PSKe2802 - 28MM X 3/4" (M) BSP, 2PSKe2803 - 28MM X 1" (M) BSP, 2PSKe3503 - 35MM X 1" (M) BSP, 2PSKe3504 - 35MM X 11/4" (M) BSP, 2PSKe4205 - 42MM X 11/2" (M) BSP, 2PSKe5406 - 54MM X 2" (M) BSP. Straight adaptor - Press fit x Swivel Female: 2PSQe1501 - 15MM X 1/2" (F) BSP SWIVEL, 2PSQe1502 - 15MM X 3/4" (F) BSP SWIVEL, 2PSQe2202 - 22MM X 3/4" (F) BSP SWIVEL, 2PSQe2203 - 22MM X 1" (F) BSP SWIVEL, 2PSQe2803 - 28MM X 1" (F) BSP SWIVEL, 2PSQe2804 - 28MM X 11/4" (F) BSP SWIVEL. Straight pipe union coupling - Press fit x Female/Male: 2PSHe1501 - 15MM X 1/2" (M) BSP UNION, 2PSHe2202 - 22MM X 3/4" (M) BSP UNION, 2PSHe2803 - 28MM X 1" (M) BSP UNION, 2PSHe3504 - 35MM X 1 1/4" (M) BSP UNION, 2PSHe4205 - 42MM X 1 1/2" (M) BSP UNION, 2PSHe5406 - 54MM X 2" (M) BSP UNION, 2PSGe1501 - 15MM X 1/2" (F) BSP UNION, 2PSGe2202 - 22MM X 3/4"(F) BSP UNION, 2PSGe2803 - 28MM X 1"(F) BSP UNION, 2PSGe3504 - 35MM X 1 1/4" (F) BSP UNION, 2PSGe4205 - 42MM X 1 1/2"(F) BSP UNION, 2PSGe5406 - 54MM X 2"(F) BSP UNION. 90°Elbow adaptor- Press fit x Female/Male: 2PSFe1501E - 15MM X 1/2" (F) BSP, 2PSFe2202E - 22MM X 3/4" (F) BSP, 2PSFe2803E - 28MM X 1" (F) BSP, 2PSKe1501E - 15MM X 1/2" (M) BSP, 2PSKe2202E - 22MM X 3/4" (M) BSP, 2PSKe2803E - 28MM X 1" (M) BSP. Elbow Wall Plate - Press fit x Female: 2PSRe1501 - 15MM X 1/2" (F) BSP. Branch Tee: Press fit x Female x Press fit: 2PSJe151501 - 15MM X 15MM X 1/2" (F) BSP, 2PSJe222201 - 22MM X 22MM X 1/2" (F) BSP, 2PSJe222202 - 22MM X 22MM X 34" (F) BSP, 2PSJe282801 - 28MM X 28MM X 1/2" (F) BSP, 2PSJe282802 - 28MM X 28MM X 3/4" (F) BSP, 2PSJe353501 - 35MM X 35MM X 1/2" (F) BSP, 2PSJe424201 - 42MM X 42MM X 1/2" (F) BSP, 2PSJe545401 - 54MM X 54MM X 1/2" (F) BSP.

Product Images

Approval Holder:

IDC Plumbing & Heating Technology (Beijing) Co., Ltd.

Company Name

IDC Plumbing & Heating Technology (Beijing) Co., Ltd.

Address

3rd Floor, Unit 2, Building 2, Section A Zhaowei Science & Technology Park No. 14, Jiuxianqiao Road Chaoyang District Beijing

Postcode

100015

Country

China

Phone

008610 51659550 ext 312

General Email

Jerry.tang@idcgroup.com.cn

View All Listings by this Company

‘Tectite 316’ range of push-fit fittings with stainless steel bodies incorporating EPDM ‘O’-rings for use with stainless steel tube (Grade 316 manufactured to EN 10312). Maximum working pressure: Fittings 15mm to 28mm 10.0 bar. Fittings 35mm to 54mm 6.0 bar. Maximum operating temperature 90°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

240702052

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See Models.

Marking:

Tectite 316 & size on body.

Installation Requirements:

R001

Expiry date:

31/07/2029

Model:

15mm TS1/TS270 Coupling 18mm TS1/TS270 Coupling 22mm TS1/TS270 Coupling 28mm TS1/TS270 Coupling 35mm TS1/TS270 Coupling 42mm TS1/TS270 Coupling 54mm TS1/TS270 Coupling 15mm TS1S/TS270S Slip Coupling 18mm TS1S/TS270S Slip Coupling 22mm TS1S/TS270S Slip Coupling 28mm TS1S/TS270S Slip Coupling 15mm x 1/2" TS2/TS270G Connector 18mm x 3/4" TS2/TS270G Connector 18mm x 1/2" TS2/TS270G Connector 22mm x 3/4" TS2/TS270G Connector 22mm x 1/2" TS2/TS270G Connector 22mm x 1" TS2/TS270G Connector 28mm x 3/4" TS2/TS270G Connector 28mm x 1" TS2/TS270G Connector 35mm x 1 1/4" TS2/TS270G Connector 42mm x 1 1/2" TS2/TS270G Connector 54mm x 2" TS2/TS270G Connector 15mm x 1/2" TS3/TS243G Connector 18mm x 3/4" TS3/TS243G Connector 18mm x 1/2" TS3/TS243G Connector 22mm x 3/4" TS3/TS243G Connector 22mm x 1/2" TS3/TS243G Connector 28mm x 3/4" TS3/TS243G Connector 28mm x 1" TS3/TS243G Connector 35mm x 1 1/4" TS3/TS243G Connector 42mm x 1 1/2" TS3/TS243G Connector 54mm x 2" TS3/TS243G Connector 18 x 15mm TS6/TS243 Reducer 22 x 15mm TS6/TS243 Reducer 22 x 18mm TS6/TS243 Reducer 28 x 15mm TS6/TS243 Reducer 28 x 18mm TS6/TS243 Reducer 28 x 22mm TS6/TS243 Reducer 35 x 22mm TS6/TS243 Reducer 35 x 28mm TS6/TS243 Reducer 42 x 22mm TS6/TS243 Reducer 42 x 28mm TS6/TS243 Reducer 42 x 35mm TS6/TS243 Reducer 54 x 35mm TS6/TS243 Reducer 54 x 42mm TS6/TS243 Reducer 15mm TS12/TS090 Elbow 18mm TS12/TS090 Elbow 22mm TS12/TS090 Elbow 28mm TS12/TS090 Elbow 35mm TS12/TS090 Elbow 42mm TS12/TS090 Elbow 54mm TS12/TS090 Elbow 15mm TS12S/TS092 Street Elbow 18mm TS12S/TS092 Street Elbow 22mm TS12S/TS092 Street Elbow 28mm TS12S/TS092 Street Elbow 15mm x 1/2" TS13/TS092G Elbow 18mm x 1/2" TS13/TS092G Elbow 22mm x 3/4" TS13/TS092G Elbw , 28mm x 1" TS13/TS092G Elbow 15mm x 1/2" TS14/TS090G Elbow 18mm x 1/2" TS14/TS090G Elbow 18mm x 3/4" TS14/TS090G Elbow 22mm x 3/4" TS14/TS090G Elbow 28mm x 1" TS14/TS090G Elbow 15mm x 1/2" TS15/TS471G Backplate Elbow 18mm x 1/2" TS15/TS471G Backplate Elbow 22mm x 3/4" TS15/TS471G Backplate Elbow 15mm TS18/TS002A Slow Bend 18mm TS18/TS002A Slow Bend 22mm TS18/TS002A Slow Bend 28mm TS18/TS002A Slow Bend 35mm TS18/TS002A Slow Bend 42mm TS18/TS002A Slow Bend 54mm TS18/TS002A Slow Bend 15mm TS18S/TS001 Elbow 18mm TS18S/TS001 Elbow 22mm TS18S/TS001 Elbow 28mm TS18S/TS001 Elbow 15mm TS21/TS041 Obtuse Elbow 18mm TS21/TS041 Obtuse Elbow 22mm TS21/TS041 Obtuse Elbow 28mm TS21/TS041 Obtuse Elbow 35mm TS21/TS041 Obtuse Elbow 42mm TS21/TS041 Obtuse Elbow 54mm TS21/TS041 Obtuse Elbow 15mm TS21S/TS040 Obtuse Street Elbow 18mm TS21S/TS040 Obtuse Street Elbow 22mm TS21S/TS040 Obtuse Street Elbow 28mm TS21S/TS040 Obtuse Street Elbow 35mm TS21S/TS040 Obtuse Street Elbow 42mm TS21S/TS040 Obtuse Street Elbow 15mm TS24/TS130 Tee 18mm TS24/TS130 Tee 22mm TS24/TS130 Tee 28mm TS24/TS130 Tee 35mm TS24/TS130 Tee 42mm TS24/TS130 Tee 54mm TS24/TS130 Tee 18 x 18 x 15mm TS25/TS130 Tee 22 x 22 x 15mm TS25/TS130 Tee 22 x 22 x 18mm TS25/TS130 Tee 28 x 28 x 15mm TS25/TS130 Tee 28 x 28 x 18mm TS25/TS130 Tee 28 x 28 x 22mm TS25/TS130 Tee 35 x 35 x 15mm TS25/TS130 Tee 35 x 35 x 22mm TS25/TS130 Tee 35 x 35 x 28mm TS25/TS130 Tee 42 x 42 x 28mm TS25/TS130 Tee 54 x 54 x 22mm TS25/TS130 Tee 54 x 54 x 28mm TS25/TS130 Tee 15 x 15mm x 1/2" TS30/TS130G Tee 18 x 18mm x 1/2" TS30/TS130G Tee 22 x 22mm x 1/2" TS30/TS130G Tee 22 x 22mm x 3/4" TS30/TS130G Tee 28 x 28mm x 1/2" TS30/TS130G Tee 35 x 35mm x 1/2" TS30/TS130G Tee 42 x 42mm x 1/2" TS30/TS130G Tee 15mm TS61/TS301 Stop End 18mm TS61/TS301 Stop End 22mm TS61/TS301 Stop End 28mm TS61/TS301 Stop End 35mm TS61/TS301 Stop End 42mm TS61/TS301 Stop End 54mm TS61/TS301 Stop End 15mm x 1/2" TS62/TS062 Tap Connector 22mm x 3/4" TS62/TS062 Tap Connector

Product Images

Approval Holder:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company

Manufacturer:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company

Range of wall mounted gas fired condensing instantaneous water heaters. Maximum working pressure 10.0bar. Maximum operating temperature 85°C.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

240704704

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP(M) for 10-12L & 14~17L/min (Flow rate) ¾” BSP(M) for 22~26L/min (Flow rate)

Marking:

Company Logo Vanward, model, pressure, tempeture and and other technical info on adhesive label on side panel.

Installation Requirements:

R001

Expiry date:

31/07/2029

Model:

10~12L balance type & forces exhaust type gas water heater: JSG=balance type gas water heater, JSQ=forces exhaust type gas water, a= nominal heat input(kW) (fixed from 20, 22 to 24), b=volume (fixed from 10, 11 to 12), STc=Sd= the type of casing (c fixed from 27, 28 to 29, d fixed from 21, 25, 22, 21B, 23, 24, 25(A), 25(B), 26, 27, 28, 31, 32, 34 to 35) Casing 1: ST27, S21, Casing 2: ST28, S25, Casing 3: ST29, S22, Casing 4: S21B, Casing 5: S23, Casing 6: S24, Casing 7: S25(A), Casing 8: S25(B), Casing 9: S26, Casing 10: S27, Casing 11: S28, Casing 12: S31, Casing 13: S32, Casing 14: S34, Casing 15: S35. Where a typical code is: ①JSG28-14ST28、JSG14ST-S25: JSG=balance type gas water heater 28=nominal heat input(kW) 14=volume ST28=the type of casing, ST=structure platform S25=the type of casing 14~17L balance type & forces exhaust type gas water heater: JSG=balance type gas water heater, JSQ=forces exhaust type gas water, a= nominal heat input(kW) (fixed from 20, 22 to 24), b=volume (fixed from 10, 11 to 12), STc=Sd= the type of casing (c fixed from 27, 28 to 29, d fixed from 21, 25, 22, 21B, 23, 24, 25(A), 25(B), 27, 28, 31, 32, 34 to 35). Same casings as above but without casing 9. ②JSG14ST-S25(B) 、JSQ28-14ST28 JSG=balance type gas water heater JSQ=forces exhaust type gas water 14=volume 28=nominal heat input(kW) ST=structure platform S25(B)=the type of casing, ST28=the type of casing 22~26L outdoor type gas water heater: JSW=outdoor type gas water heater, a= nominal heat input(kW) (fixed from 44 to 52), b=volume (fixed from 22 to 26), ST58=Wd= the type of casing (d fixed from 81, 82, 83 to 84), Casing 1: ST58, W81, Casing 2: W82, Casing 3: W83, Casing 4: W84. ③JSW44-22ST58、 JSW22HT-W81: JSW=outdoor type gas water heater 44=nominal heat input(kW) 22=volume ST58=the type of casing, HT=structure platform W81=the type of casing

JSG20-10ST27, JSG10ST-S21, JSQ20-10ST27, JSQ10ST-S21, JSG22-11ST27, JSG11ST-S21, JSQ22-11ST27, JSQ11ST-S21, JSG24-12ST27, JSG12ST-S21, JSQ24-12ST27, JSQ12ST-S21, JSG20-10ST28, JSG10ST-S25, JSQ20-10ST28, JSQ10ST-S25, JSG22-11ST28, JSG11ST-S25, JSQ22-11ST28, JSQ11ST-S25, JSG24-12ST28, JSG12ST-S25, JSQ24-12ST28, JSQ12ST-S25, JSG20-10ST29, JSG10ST-S22, JSQ20-10ST29, JSQ10ST-S22, JSG22-11ST29, JSG11ST-S22, JSQ22-11ST29, JSQ11ST-S22, JSG24-12ST29, JSG12ST-S22, JSQ24-12ST29, JSQ12ST-S22, JSG10ST-S21B, JSQ10ST-S21B, JSG11ST-S21B, JSQ11ST-S21B, JSG12ST-S21B, JSQ12ST-S21B, JSG10ST-S23, JSQ10ST-S23, JSG11ST-S23, JSQ11ST-S23, JSG12ST-S23, JSQ12ST-S23, JSG10ST-S24, JSQ10ST-S24, JSG11ST-S24, JSQ11ST-S24, JSG12ST-S24, JSQ12ST-S24, JSG10ST-S25(A), JSQ10ST-S25(A), JSG11ST-S25(A), JSQ11ST-S25(A), JSG12ST-S25(A), JSQ12ST-S25(A), JSG10ST-S25(B), JSQ10ST-S25(B), JSG11ST-S25(B), JSQ11ST-S25(B), JSG12ST-S25(B), JSQ12ST-S25(B), JSG10ST-S26, JSQ10ST-S26, JSG12ST-S26, JSQ12ST-S26, JSG10ST-S27, JSQ10ST-S27, JSG12ST-S27, JSQ12ST-S27, JSG10ST-S28, JSQ10ST-S28, JSG12ST-S28, JSQ12ST-S28, JSG10ST-S31, JSQ10ST-S31, JSG12ST-S31, JSQ12ST-S31, JSG10ST-S32, JSQ10ST-S32, JSG12ST-S32, JSQ12ST-S32, JSG10ST-S34, JSQ10ST-S34, JSG12ST-S34, JSQ12ST-S34, JSG10ST-S35, JSQ10ST-S35, JSG11ST-S35, JSQ11ST-S35, JSG12ST-S35, JSQ12ST-S35. JSG28-14ST27, JSG14ST-S21, JSQ28-14ST27, JSQ14ST-S21, JSG30-16ST27, JSG16ST-S21, JSQ30-16ST27, JSQ16ST-S21, JSG31-17ST27, JSG17ST-S21, JSQ31-17ST27, JSQ17ST-S21, JSG28-14ST28, JSG14ST-S25, JSQ28-14ST28, JSQ14ST-S25, JSG30-16ST28, JSG16ST-S25, JSQ30-16ST28, JSQ16ST-S25, JSG31-17ST28, JSG17ST-S25, JSQ31-17ST28, JSQ17ST-S25, JSG28-14ST29, JSG14ST-S22, JSQ28-14ST29, JSQ14ST-S22, JSG30-16ST29, JSG16ST-S22, JSQ30-16ST29, JSQ16ST-S22, JSG31-17ST29, JSG17ST-S22, JSQ31-17ST29, JSQ17ST-S22, JSG14ST-S21B, JSQ14ST-S21B, JSG16ST-S21B, JSQ16ST-S21B, JSG17ST-S21B, JSQ17ST-S21B, JSG14ST-S23, JSQ14ST-S23, JSG16ST-S23, JSQ16ST-S23, JSG17ST-S23, JSQ17ST-S23, JSG14ST-S24, JSQ14ST-S24, JSG16ST-S24, JSQ16ST-S24, JSG17ST-S24, JSQ17ST-S24, JSG14ST-S25(A), JSQ14ST-S25(A), JSG16ST-S25(A), JSQ16ST-S25(A), JSG17ST-S25(A), JSQ17ST-S25(A), JSG14ST-S25(B), JSQ14ST-S25(B), JSG16ST-S25(B), JSQ16ST-S25(B), JSG17ST-S25(B), JSQ17ST-S25(B), JSG14ST-S27, JSQ14ST-S27, JSG16ST-S27, JSQ16ST-S27, JSG14ST-S28, JSQ14ST-S28, JSG16ST-S28, JSQ16ST-S28, JSG14ST-S31, JSQ14ST-S31, JSG16ST-S31, JSQ16ST-S31, JSG14ST-S32, JSQ14ST-S32, JSG16ST-S32, JSQ16ST-S32, JSG14ST-S34, JSQ14ST-S34, JSG16ST-S34, JSQ16ST-S34, JSG14ST-S35, JSQ14ST-S35,JSG16ST-S35, JSQ16ST-S35. JSW44-22ST58, JSW22HT-W81, JSW52-26ST58, JSW26HT-W81, JSW22HT-W82, JSW26HT-W82, JSW22HT-W83, JSW26HT-W83, JSW22HT-W84, JSW26HT-W84.

Product Images

Approval Holder:

Guangdong Vanward New Electric Co. Ltd.

Company Name

Guangdong Vanward New Electric Co. Ltd.

Address

13 Jianye Mid- Road Shunde High Tech Industry Development Zone

Country

Ronggui Shunde

View All Listings by this Company

Manufacturer:

Guangdong Vanward New Electric Co. Ltd.

Company Name

Guangdong Vanward New Electric Co. Ltd.

Address

13 Jianye Mid- Road Shunde High Tech Industry Development Zone

Country

Ronggui Shunde

View All Listings by this Company

Octave range of water meters with blue epoxy coated cast iron or plastic bodies (see models). Maximum working pressure 16.0 Bar. Maximum operating temperature 50.0°C

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models

Marking:

CZUS & Company logo on cap. Company Information,, product information and model range on label under the plastic lid.

Installation Requirements:

R001

Expiry date:

31/05/2029

Model:

CZUS 13905XXX DN: 40 mm (Composite Body, 2" BSP (M) 1CZUS 13915XXX COMPOSITE BODY DN: 50 mm 2.1/4" BSP (M) CZUS 139XXXXX IRON BODY DN: 50-300 mm (Iron Body, 2” to 12”) 13905 & 13915: Where the XXX denotes customer specifications, e.g. flow rate, ration, packaging or logistic specifications. 139XXXXX: Where the 1st X denotes the size, and can be replaced with any of the following: 1 = 2” Flanged, 2 = 2.1/2” Flanged, 3 = 3” Flanged, 4 = 4” Flanged, 5 = 6” Flanged, 6 = 8” Flanged, 7 = 10” Flanged, 8 = 12” Flanged, Where the 2nd X denotes body type and customer specific and can be replaced with any of the following: 5 = Composite body, All other numbers = Customer specific Where the 3rd, 4th and 5th X’s denotes customer specifications, e.g. flow rate, ration, packaging or logistic specifications.

Approval Holder:

Contadores De Agua De Zaragoza S.A. (Contazara S.A.)

Company Name

Contadores De Agua De Zaragoza S.A. (Contazara S.A.)

Address

Carretera Castellon KM. 5 5 50720 Zaragoza Spain

View All Listings by this Company

Range of inline and manifold water meters with brass bodies and stainless-steel strainers on the inlets. Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Inline models. 1" BSP (M) Manifold models 1 ½” BSP (M)

Marking:

Itron logo, model code, serial number, date of manufacture (YYYY) on dial face.

Installation Requirements:

R001

Expiry date:

31/07/2029

Model:

P50-I Aquadis+ DN20 inline P50-M Aquadis+ DN20 manifold

Product Images

Approval Holder:

Itron Metering Solutions UK Ltd

Company Name

Itron Metering Solutions UK Ltd

Address

Unit 10, Haven Exchange Felixstowe Suffolk

Postcode

IP11 2QX

Phone

+44 161 865 1181

View All Listings by this Company

Manufacturer:

ITRON France SAS

Company Name

ITRON France SAS

Address

9 rue Ampère Mâcon

Postcode

71031

Country

France

Phone

+33 6 43 94 48 08

View All Listings by this Company