‘NMSP2104 M'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual ‘specification no. PIN-10’, revision no. '0' dated '15/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SWEP Sealix Coating'. Factory applied, colourless (translucent) silicon dioxide coating. Apply as per manufacturing instructions ref. 'Sealix-2020-01' dated 2020-01-01. Cure for 3 hours@300°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EB-1003'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'Fowry Powder-001' dated '2020.3.20'. For use with water up to 85°C.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPY2-II'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user instruction 'REV-202012-2' dated '11.12.2020'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC3 Blue PTFE Coating'. Blue coloured, factory applied, PTFE coating intended to coat 'O' rings. Apply and cure as per manufacturer's instructions 'LDAP-007 issue 1' dated 11/02/2020. For use with water up to 85°C.
Page 13 of 15
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
