Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.

Section:

1890 Unvented Heating Apparatus

Size:

28mm compression.

Marking:

Manufacturers name, address, date of manufacturer, capacity, model no, serial no, pressure and technical information.

Installation Requirements:

R001 R140 R360 R511 R530

Expiry date:

31/05/2028

Model:

IDEPLUHP150PPSZ & IDEPLUHP180PPSZ: 550mm diameter; 150, 180; litre; single coil cylinders intended for coupling with a range of heat pumps 5kW to 14kW; Pre-plumbed and pre-wired. Single zone. IDEPLUHP150PPSZSL & IDEPLUHP180PPSZSL: 475mm diameter; 150, 180, litre; single coil cylinders intended for coupling with a range of heat pumps 5kW to 14kW; Pre-plumbed and pre-wired; single zone. IDEPLUHP210PPDZ, IDEPLUHP250PPDZ & IDEPLUHP300PPDZ: 550mm diameter; 210, 250, 300 litre; single coil cylinders intended for coupling with a range of heat pumps 5kW to 14kW; Pre-plumbed and pre-wired. Two zone. IDEPLUHP210PPDZSL: 475mm diameter; 210 litre; single coil cylinders intended for coupling with a range of heat pumps 5kW to 14kW; Pre-plumbed and pre-wired. Two zone. IDEPLUHP180DUOPPSZ & IDEPLUHP210DUOPPSZ: 550mm diameter 180, 210, litre; single coil cylinders on top of a buffer cylinder for coupling with a range of heat pumps 5kW to 14kW; Pre-plumbed and pre-wired; single zone. IDEPLUHP250DUOPPSZ & IDEPLUHP300DUOPPSZ: 630mm diameter 250, 300 litre; single coil cylinders on top of a buffer cylinder for coupling with a range of heat pumps 5kW to 14kW; Pre-plumbed and pre-wired; single zone. IDEPLUHP180DUOPPDZ & IDEPLUHP210DUOPPDZ: 550mm diameter 180, 210, litre; single coil cylinders on top of a buffer cylinder for coupling with a range of heat pumps 5kW to 14kW; Pre-plumbed and pre-wired; two zone. IDEPLUHP250DUOPPDZ & IDEPLUHP300DUOPPDZ: 630mm diameter 250, 300 litre; single coil cylinders on top of a buffer cylinder for coupling with a range of heat pumps 5kW to 14kW; Pre-plumbed and pre-wired; two zone. IDEPLUHP400: 630mm diameter; 400 litre; single coil cylinders intended for coupling with a range of heat pumps 5kW to 14 kW. IDEPLU090MB: 630mm diameter; 90 litre; buffer cylinder for coupling with a range of heat pumps 5kW to 14kW; and any cylinder without a buffer.

Product Images

Approval Holder:

Ideal Boilers Ltd

Company Name

Ideal Boilers Ltd

Address

PO Box 103 National Avenue Hull East Yorkshire

Postcode

HU5 4JN

Country

United Kingdom

Phone

07775659359

General Email

ben.higinbotham@groupe-atlantic.co.uk

View All Listings by this Company

`354` range of distribution manifolds with DZR brass bodies and multiple (2, 3, 4 or 5) shut off valves for hot and cold water services, for use with copper tube to (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1950 Manifolds

Section Subtitle:

Metal.

WRAS Approval Number:

2403800

Size:

See model

Marking:

Caleffi logo on body and operating member. CR on body.

Installation Requirements:

R001

Expiry date:

31/03/2029

Model:

354052 Manifold: ¾” BSP (F) x ¾” BSP (M) x ø23mm 2 connections. 354053 Manifold: ¾” BSP (F) x ¾” BSP (M) x ø23mm 3 connections. 354054 Manifold: ¾” BSP (F) x ¾” BSP (M) x ø23mm 4 connections. 354055 Manifold: ¾” BSP (F) x ¾” BSP (M) x ø23mm 5 connections. Models added September 2024: 354252 Manifold: ¾” BSP (F) x ¾” BSP (M) x ½” BSP (M) 2 connections. 354253 Manifold: ¾” BSP (F) x ¾” BSP (M) x ½” BSP (M) 3 connections. 354254 Manifold: ¾” BSP (F) x ¾” BSP (M) x ½” BSP (M) 4 connections. 354255 Manifold: ¾” BSP (F) x ¾” BSP (M) x ½” BSP (M) 5 connections.

Product Images

Approval Holder:

Caleffi S.p.A

Company Name

Caleffi S.p.A

Address

Strada Regionale 229 n. 25 Fontaneto d'Agogna (NO)

Postcode

28010

Country

Italy

Phone

+39 0322 8491

General Email

gary.perry@caleffi.com

View All Listings by this Company

Manufacturer:

Caleffi S.p.A

Company Name

Caleffi S.p.A

Address

Strada Regionale 229 n. 25 Fontaneto d'Agogna (NO)

Postcode

28010

Country

Italy

Phone

+39 0322 8491

General Email

gary.perry@caleffi.com

View All Listings by this Company

Range of Wall mounted, concealed, manually operated blending valves incorporating brass bodies (various finishes) and a ceramic cartridge headwork and single lever operating member. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 70°C

Section:

2000 Shower Valves

Section Subtitle:

Shower valve(s) with manual temperature control.

WRAS Approval Number:

2309050

Note:

The rough in kit is not approved in its own right.

Size:

Specifically for use with rough kit 01800180 which has ¾” BSP (F) inlets.

Marking:

Hansgrohe logo on rough kit body and operating member

Installation Requirements:

R001 R010

Expiry date:

30/09/2028

Model:

31 652 xx0 71 768 xx0 Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

2D & 3D range of thermostatic blending valves (brass bodies – various finishes) incorporating a 2 way diverter with 2 models having an additional diverter control to shower outlet. The products include various operating members and faceplates. Both inlets incorporate a stainless steel strainer and an approved check valve cartridge, however it has not been fully tested to demonstrate it provides adequate backflow protection. Available without or with in-wall fixing box Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

2000 Shower Valves

Section Subtitle:

Shower valve(s) with manual temperature control.

WRAS Approval Number:

2309311

Size:

½” BSP (F)

Marking:

Methven etched on face plate

Installation Requirements:

R001 R010 R040

Expiry date:

30/09/2028

Model:

AIO 2D AIO 2DBK KAHA 2D KAHA 2DA KAHA 2DBB KAHA 2DBK KAHA 2DBN KAHA 2DGM KIRI 2D KIRI 2DA KIRI 2DBB KIRI 2DBK KIRI 2DBN KIRI 2DGM TUROA 2D VALVE 2D KAHA 3D KAHA 3DA KAHA 3DBB KAHA 3DBK KAHA 3DBN KAHA 3DGM KIRI 3D KIRI 3DA KIRI 3DBB KIRI 3DBK KIRI 3DBN KIRI 3DGM VALVE 3D

Product Images

Approval Holder:

Methven UK Limited

Company Name

Methven UK Limited

Address

3-3A Stone Cross Court Yew Tree Way Golborne Warrington

Postcode

WA3 3JE

Country

United Kingdom

Phone

0800 195 1602

General Email

raluca.olariu@uk.methven.com

View All Listings by this Company

Range of thermal circulation valves with gunmetal bodies and EPDM ‘O’-rings. Models incorporate drain valves. Maximum operating pressure 16.0 bar. Maximum operating temperature 90°C.

Section:

2010 Shower Valves

Section Subtitle:

Shower valve(s) with thermostatic temperature control

WRAS Approval Number:

2307044

Size:

4205504 – ½” BSP (F), 4205506 – ¾” BSP (F), 4205508 – 1” BSP (F). 4206504 – ¾” BSP (M), 4206506 – 1” BSP (M), 4206508 – 1 ¼” BSP (M),

Marking:

Oventrop logo (OV), RG, size, PN, flow arrow, DVGW on body. Oventrop, size, Aquastrom on valve head.

Installation Requirements:

R001 R511

Expiry date:

31/07/2028

Model:

4205504 - Aquastrom T plus Thermal circulation valve with internal thread, 4205506 - Aquastrom T plus Thermal circulation valve with internal thread, 4205508 - Aquastrom T plus Thermal circulation valve with internal thread, 4206504 - Aquastrom T plus Thermal circulation valve with flat sealing external thread, 4206506 - Aquastrom T plus Thermal circulation valve with flat sealing external thread, 4206508 - Aquastrom T plus Thermal circulation valve with flat sealing external thread.

Product Images

Approval Holder:

Oventrop GmbH & Co KG

Company Name

Oventrop GmbH & Co KG

Address

Paul-Oventrop-Strasse 1, 59939 Olsberg

Country

Germany

View All Listings by this Company