‘AF’ range of compression fittings with brass or chrome plated brass bodies for use with copper pipe (manufactured to EN1057). The AF14 and AF15 tap connector models incorporate an EPDM washer. Maximum working pressure 16.0 bar. Maximum working temperature 85˚C

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2204071

Size:

see model

Marking:

“DOZ” and Size on fitting body

Installation Requirements:

R001

Expiry date:

30/04/2027

Model:

AF01 couplings-cxc: 6 - 54mm compression. AF01B repair couplings-cxc: 6 - 54mm compression. AF01R reducing couplings cxc: 10 x 8mm compression, 12 x 8mm compression, 15 x 8mm compression, 12 x 10mm compression, 15 x 10mm compression, 15 x 12mm compression, 18 x 12mm compression, 16 x 15mm compression, 22 x 15mm compression, 28 x 15mm compression, 28 x 22mm compression, 35 x 28mm compression, 42 x 35mm compression, 54 x 42mm compression. AF02P female adaptors-parallel: 6mm compression, x ¼" BSP (F), 6mm compression, x ⅜" BSP (F), 8mm compression, x ⅜" BSP (F), 8mm compression, x ¼" BSP (F), 10mm compression, x ¼" BSP (F), 10mm compression, x ⅜" BSP (F), 10mm compression, x ½" BSP (F), 12mm compression, x ¼" BSP (F), 12mm compression, x ⅜" BSP (F), 12mm compression, x ½" BSP (F), 15mm compression, x ¼" BSP (F), 15mm compression, x ⅜" BSP (F), 15mm compression, x ½" BSP (F), 15mm compression, x ¾" BSP (F), 18mm compression, x ½" BSP (F), 22mm compression, x ½" BSP (F), 22mm compression, x ¾" BSP (F), 22mm compression, x 1" BSP (F), 28mm compression, x 1" BSP (F), 28mm compression, x ¾” BSP (F), 35mm compression, x 1-¼" BSP (F), 42mm compression, x 1-½" BSP (F), 54mm compression, x 2" BSP (F). AF03T male adaptors-CxMI taper: 6mm compression, x ¼" BSP (M), 6mm compression, x ⅜" BSP (M), 8mm compression, x ¼" BSP (M), 8mm compression, x ⅜" BSP (M), 8mm compression, x ½" BSP (M), 10mm compression, x ¼" BSP (M), 10mm compression, x ⅜" BSP (M), 10mm compression, x ½" BSP (M), 12mm compression, x ¼" BSP (M), 12mm compression, x ⅜" BSP (M), 12mm compression, x ½" BSP (M), 15mm compression, x ⅜" BSP (M), 15mm compression, x ¼" BSP (M), 15mm compression, x ½" BSP (M), 15mm compression, x ¾" BSP (M), 18mm compression, x ½" BSP (M), 22mm compression, x ½" BSP (M), 22mm compression, x ¾" BSP (M), 22mm compression, x 1" BSP (M), 28mm compression, x ¾" BSP (M), 28mm compression, x 1" BSP (M), 35mm compression, x 1-¼" BSP (M), 42mm compression, x 1-½" BSP (M), 54mm compression, x 2" BSP (M). AF03P male adaptors-CxMI parallel: 6mm compression, x ¼" BSP (M), 6mm compression, x ⅜" BSP (M), 8mm compression, x ¼" BSP (M), 8mm compression, x ⅜" BSP (M), 8mm compression, x ½" BSP (M), 10mm compression, x ¼" BSP (M), 10mm compression, x ⅜" BSP (M), 10mm compression, x ½" BSP (M), 12mm compression, x ¼" BSP (M), 12mm compression, x ⅜" BSP (M), 12mm compression, x ½" BSP (M), 15mm compression, x ⅜" BSP (M), 15mm compression, x ¼" BSP (M), 15mm compression, x ½" BSP (M), 15mm compression, x ¾" BSP (M), 18mm compression, x ½" BSP (M), 22mm compression, x ½" BSP (M), 22mm compression, x ¾" BSP (M), 22mm compression, x 1" BSP (M), 28mm compression, x ¾" BSP (M), 28mm compression, x 1" BSP (M), 35mm compression, x 1-¼" BSP (M), 42mm compression, x 1-½" BSP (M), 54mm compression, x 2" BSP (M). AF03P extended male adaptors-CxMI: 10mm compression, x ⅜" BSP (M), 12mm compression, x ⅜" BSP (M), 15mm compression, x ½" BSP (M), 22mm compression, x ¾" BSP (M), 28mm compression, x 1" BSP (M). AF04 tank connectors-lug style: 10 - 54mm compression. AF04N tank connectors-nut style: 10 - 54mm compression. AF05 elbows 90 degree-CxC: 6 - 54mm compression. 8 x 6mm compression, 10 x 8mm compression, 12 x 10mm compression, 15 x 12mm compression, 18 x 15mm compression, 22 x 15mm compression, 22 x 18mm compression, 28 x 22mm compression, 35 x 28mm compression, 42 x 35mm compression, 54 x 42mm compression, AF06T male elbows-CxMI taper: 6mm compression, x ¼" BSP (M), 6mm compression, x ⅜" BSP (M), 8mm compression, x ¼" BSP (M), 8mm compression, x ⅜" BSP (M), 10mm compression, x ¼" BSP (M), 10mm compression, x ⅜" BSP (M), 10mm compression, x ½" BSP (M), 12mm compression, x ¼" BSP (M), 12mm compression, x ⅜" BSP (M), 12mm compression, x ½" BSP (M), 15mm compression, x ¼" BSP (M), 15mm compression, x ⅜" BSP (M), 15mm compression, x ½" BSP (M), 15mm compression, x ¾" BSP (M), 18mm compression, x ½" BSP (M), 22mm compression, x ½" BSP (M), 22mm compression, x ¾" BSP (M), 22mm compression, x 1" BSP (M), 28mm compression, x ¾" BSP (M), 28mm compression, x 1" BSP (M), 35mm compression, x 1¼" BSP (M), 42mm compression, x 1½" BSP (M), 54mm compression, x 2" BSP (M). AF06P male elbows-CxMI parallel: 6mm compression, x ¼" BSP (M), 6mm compression, x ⅜" BSP (M), 8mm compression, x ¼" BSP (M), 8mm compression, x ⅜" BSP (M), 10mm compression, x ¼" BSP (M), 10mm compression, x ⅜" BSP (M), 10mm compression, x ½" BSP (M), 12mm compression, x ¼" BSP (M), 12mm compression, x ⅜" BSP (M), 12mm compression, x ½" BSP (M), 15mm compression, x ¼" BSP (M), 15mm compression, x ⅜" BSP (M), 15mm compression, x ½" BSP (M), 15mm compression, x ¾" BSP (M), 18mm compression, x ½" BSP (M), 22mm compression, x ½" BSP (M), 22mm compression, x ¾" BSP (M), 22mm compression, x 1" BSP (M), 28mm compression, x ¾" BSP (M), 28mm compression, x 1" BSP (M), 28mm compression, x 1-¼" BSP (M), 35mm compression, x 1-¼" BSP (M), 42mm compression, x 1-½" BSP (M), 54mm compression, x 2" BSP (M). AF07 female elbows-CxFI parallel: 6mm compression, x ¼" BSP (F), 6mm compression, x ⅜" BSP (F), 8mm compression, x ¼" BSP (F), 8mm compression, x ⅜" BSP (F), 10mm compression, x ¼" BSP (F), 10mm compression, x ½" BSP (F), 10mm compression, x ⅜" BSP (F), 12mm compression, x ¼" BSP (F), 12mm compression, x ⅜" BSP (F), 12mm compression, x ½" BSP (F), 15mm compression, x ¼" BSP (F), 15mm compression, x ⅜" BSP (F), 15mm compression, x ½" BSP (F), 15mm compression, x ¾" BSP (F), 18mm compression, x ½" BSP (F), 22mm compression, x ½" BSP (F), 22mm compression, x ¾" BSP (F), 22mm compression, x 1" BSP (F), 28mm compression, x ¾" BSP (F), 28mm compression, x 1" BSP (F), 28mm compression, x 1-¼" BSP (F), 35mm compression, x 1-¼" BSP (F), 42mm compression, x 1-½" BSP (F), 54mm compression, x 2" BSP (F). AF08 wallplate elbows-CxFI: 12mm compression, x ⅜" BSP (F), 15mm compression, x ½" BSP (F), 22mm compression, x ¾" BSP (F), 22mm compression, x ½" BSP (F), 28mm compression, x 1" BSP (F). AF08 equal tees-CxCxC: 6 - 54mm compression. AF08R reducing tees-CxCxC: 15 x 15 x 10mm compression, 15 x 15 x 22mm compression, 22 x 15 x 15mm compression, 22 x 15 x 22mm compression, 22 x 22 x 15mm compression, 22 x 22 x 28mm compression, 28 x 15 x 28mm compression, 28 x 22 x 28mm compression, 28 x 22 x 22mm compression, 28 x 28 x 15mm compression, 28 x 28 x 22mm compression, 35 x 35 x 15mm compression, 35 x 35 x 22mm compression, AF09 threaded centre teesCxCxFI: 15mm compression, x 15mm compression, x ¼" BSP (F), 15mm compression, x 15mm compression, x ½" BSP (F), 22mm compression, x 22mm compression, x ½" BSP (F), 22mm compression, x 22mm compression, x ¾" BSP (F), 28mm compression, x 28mm compression, x ¾" BSP (F), 28mm compression, x 28mm compression, x 1" BSP (F). AF10 threaded end tees CxFIxC: 15mm compression, x ½" BSP (F) x 15mm compression, 22mm compression, x ¾" BSP (F) x 22mm compression, AF12 stopends-C: 6 - 54mm compression. AF14 straight tap connectors: 15mm compression, x ½" BSP (F), 15mm compression, x ¾" BSP (F), 22mm compression, x ¾" BSP (F), 22mm compression, x 1" BSP (F). AF15 bent tap connectors: 15mm compression, x ½" BSP (F).

Product Images

Approval Holder:

Hangzhou DOZ Import & Export Co., Ltd

Company Name

Hangzhou DOZ Import & Export Co., Ltd

Address

Room 302, Binke Mansion, No. 1503, Xipu Road, Binjiang District, Hangzhou Zhejiang 310053

Country

China

Phone

86 571 28180555

View All Listings by this Company

Manufacturer:

Hangzhou DOZ Import & Export Co., Ltd

Company Name

Hangzhou DOZ Import & Export Co., Ltd

Address

Room 302, Binke Mansion, No. 1503, Xipu Road, Binjiang District, Hangzhou Zhejiang 310053

Country

China

Phone

86 571 28180555

View All Listings by this Company

Low profile mechanical seal intended for the internal repair of pipe joints. The system incorporates two stainless steel compression rings and an EPDM seal. For above and below ground use. Maximum working pressure 22.5 bar. Cold water use only.

Section:

1220 Fittings for use with Tube and Pipe

Section Subtitle:

Flanged, un-flanged and repair clamps. (external clamps only) Unless specified in the individual approval, the products within this section are not suitable for below ground use WRAS takes no responsibility for the claims made by the manufacturer regarding the effectiveness of the product for providing a repair to fittings to prevent a waste of water.

WRAS Approval Number:

2111030

Size:

DN600

Marking:

Amex-10 printed on inside of seal and clamp.

Installation Requirements:

R001

Expiry date:

30/11/2026

Model:

AMEX-10 SEAL

Product Images

Approval Holder:

Planned Maintenance (Pennine) Ltd

Company Name

Planned Maintenance (Pennine) Ltd

Address

Bentley Wood Way Burnley

Postcode

BB11 5ST

View All Listings by this Company

Range of stainless-steel plate heat exchangers with EPDM gaskets. The primary circuit, (excluding the E2 prefix models), incorporates a drain valve and a pump (excluding STP prefix models including an ‘N’ as the 14th figure). Operating parameters: Maximum working pressure of the secondary circuit: 6.0 bar or 10.0 bar (see model). Maximum working pressure of the primary circuit: E4 models: 6.0 bar. C3, E3, E2, i2: 10.0 bar. Models added February 2023 – Econoplate STP3, STC3, STP2, STC2 & STP4: 10.0 bar. Maximum operating temperature: Primary 140°C & Secondary 85°C.

Section:

1350 Heat Exchangers

Size:

Secondary: 1½” BSP (F) or 2” BSP (F), as well as 1” BSP (F) recirculation connection where fitted. Primary: DN40 or DN50 flanged inlet, 1½” BSP (M) or 2” BSP (M) outlet.

Marking:

Stokvis logo, Stokvis, Econoplate & model, pressure, flow rate, WRAS and other technical information on data plate on body.

Installation Requirements:

R001 R511

Expiry date:

31/01/2027

Model:

Econoplate models: Following models xx goes from 5-59 to denote number of plates. E4Axx, E4Aixx, E4Bxx, E4Bixx, E3A1xx, E3Ai1xx, C3Ai1xx, E3A3xx, E3Ai3xx, C3Ai3xx, i2Axx, i2Bxx, E2A(##)xx, E2B(##)xx, E4AxxD, E4AixxD, E4BxxD, E4BixxD, E3A1xxD, E3Ai1xxD, C3Ai1xxD, E3A3xxD, E3Ai3xxD, C3Ai3xxD, i2AxxD, i2BxxD. Following models xx goes from 11-74 to denote number of plates: E3Cxx, E3Cixx, C3Cixx, i2Cxx, E2C(##)xx, E3CxxD, E3CixxD, C3CixxD, i2CxxD. FIRST LETTER: E = MODELS PAINTED YELLOW. C = MODELS ARE IDENTICAL TO E MODELS BUT PAINTED WHITE. i = Fitted with a speed controlled primary pump (2 port models only). FIRST NUMBER: PRIMARY CONTROL VALVE TYPE/NO. OF PORTS - 2, 3 or 4. NEXT LETTER RELATES TO FRAME SIZE OR PRIMARY CONTROL SET (PUMP & OR CONTROL VALVE) SIZE: Frame size - A, B or C. When fitted with a speed controlled primary pump add an i (3 and 4 port models only). When fitted with twin head primary pump add a D to model designation after the number xx. xx = number of (heat exchanger) plates All model names are followed by +0R where: +0R = no secondary pump. ## added to differentiate primary fluids and can be replaced with the following: SW = steam to water. LTHWS = low temperature heating to domestic hot water. MTHWS = medium temperature heating to domestic hot water. Units with a secondary pressure of 10.0 bar use stainless connections and are denoted by ’10 bar’ at end of model number. Units with a secondary pressure of 6.0 bar use bronze connections which are standard fitment so no addition or alteration to model number. All models can be fitted with either 1.5” or 2” secondary circuit connections, this does not affect the product model number. Models added February 2023 - Econoplate STP3, STC3, STP2, STC2 & STP4: ST (first 2 figures) – Signifies a Stokvis product on all models. All Econoplate models are orange in colour. P or C (3rd figure) – Signifies small or large chassis (P = 1.5” primary connections, C = 2” primary connections). 2, 3, or 4 (4th figure) – Signifies configuration of chassis to suit control valve, 2, 3 or 4 port. A, B, or C (5th figure) – Signifies secondary connection sizes (A = 1.5”, B = 2.0”, C = 2.0” stainless). 5 – 59 (P chassis), 11 – 74 (C chassis) (6th & 7th figure) – Signifies number of identical plates on unit. H, L, or M (8th Figure) – Signifies heat exchanger plate design (H = High theta, L = Low theta, M (mixed) = Combination of H & L). T1 or T2 (9th & 10th figure) – Signifies type of control panel (T1 = Standard control panel, T2 = Touchscreen premium panel). 2, 3, or 4 (11th figure) – Signifies primary control valve/s configuration (2 = 2 port, 3 = 3 port, 4 = 4 port). S, D, or N (12th figure) – Signifies primary pump configuration (S = Single head, D = Dual head, N = No primary pump fitted). 1 or 4 (13th figure) – Signifies number of temp sensors fitted to unit (1 = 1, 4 = 4). N (14th Figure) – Signifies no secondary pump fitted. Example: STP3A17HT13S4N

Product Images

Approval Holder:

Stokvis Energy Systems

Company Name

Stokvis Energy Systems

Address

96R Walton Road East Molesey Surrey

Country

KT8 0DL

View All Listings by this Company

Manufacturer:

Stokvis Energy Systems

Company Name

Stokvis Energy Systems

Address

96R Walton Road East Molesey Surrey

Country

KT8 0DL

View All Listings by this Company

‘POD’ range of indirect and direct heat interface units providing space heating and instantaneous hot water. The heat transfer is generated via plate heat exchangers. The domestic hot water (DHW) circuit incorporates an adjustable temperature mixing valve. The indirect models incorporate an expansion vessel (on the CW inlet of the DHW circuit) and a pressure relief valve set at 3.0 bar (on the space heating circuit). The indirect models only are supplied with a temporary filling loop, which comprises of a stainless steel braided EPDM lined flexible hose assembly and a lever operated spherical valve for connection to the primary circuit. The angled cold water inlet incorporates an isolation valve and a branch to connect to the filling loop, which includes a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3). Maximum working pressure for indirect units: Primary circuit: 16.0 bar. Space heating: 2.5 bar. Secondary circuit (DHW): 10.0 bar. Maximum working pressure for direct units: Primary circuit: 10.0 bar. Space heating: 10.0 bar. Secondary circuit (DHW): 10.0 bar. Maximum operating temperature for domestic hot water 65°C. Maximum operating temperature for central heating and primary circuit 85°C.

Section:

1350 Heat Exchangers

Size:

22mm copper pipe connection.

Marking:

Ideal Heating badge and model on adhesive label on front casing. Manufacturer, serial number, model number, pressure rating and other technical information on data label within appliance.

Installation Requirements:

R001 R140 R360

Expiry date:

30/04/2027

Model:

POD range of indirect (i prefix) and direct (d prefix) HIU: i305, i405, i505, i605, i705, d30, d40, d50, d60. All models can have the following suffixes to denote the inclusion of a heat meter: HWM for a hard wired MBUS and WLM for a wireless MBUS.

Product Images

Approval Holder:

Ideal Boilers Ltd

Company Name

Ideal Boilers Ltd

Address

PO Box 103 National Avenue Hull East Yorkshire

Postcode

HU5 4JN

Country

United Kingdom

Phone

07775659359

General Email

ben.higinbotham@groupe-atlantic.co.uk

View All Listings by this Company

Manufacturer:

Ideal Boilers Ltd

Company Name

Ideal Boilers Ltd

Address

PO Box 103 National Avenue Hull East Yorkshire

Postcode

HU5 4JN

Country

United Kingdom

Phone

07775659359

General Email

ben.higinbotham@groupe-atlantic.co.uk

View All Listings by this Company

Range of water meters with a brass body, EPDM ‘O’-rings and seal. The products incorporate an internal plastic strainer and an optional combined plastic and stainless-steel strainer on the inlet. Maximum working pressure 16.0 bar. Cold water use only

Section:

1505 Water Meters

Size:

1”, 1½” and 2” BSP (M).

Marking:

Diehl Metering, Altair, made in France and technical information on meter face. Material and flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/06/2027

Model:

ALTAIR V4 DN25 / DN32 / DN40 - Type A2

Approval Holder:

Diehl Metering S.A.S & Diehl Metering Sp. Z o.o.

Company Name

Diehl Metering S.A.S & Diehl Metering Sp. Z o.o.

Country

View All Listings by this Company