Water Regulations Approval Scheme Ltd

Thomas Dudley Ltd Approvals

WRAS Approval Number: #2202903

Single flush pneumatically operated drop valve with a rubber seating washer and ABS body. The valve is operated by a separate push button assembly.

Section:: 1305 Flushing Mechanisms
Section Subtitle:: WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not be verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.
WRAS Approval Number:: 2202903
Expiry date:: 28/02/2027
Size:: 2” BSP Outlet
Marking:: Dudley on adhesive label on valve body
Installation Requirements:: R001
Model:: Pinto Valve
Factor:: Thomas Dudley Ltd

Company Name
Thomas Dudley Ltd
Address
Dauntless Works PO Box 28 New Birmingham Road
Postcode
DY1 4SN
Phone
Tel: 0121 557 5411 Fax: 0121 557 5345
General Email
info@thomasdudley.co.uk

View All Listings by this Company

WRAS Approval Number: #2112907

BS EN 14055 (2018) WC Cistern incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a lever operated dual flush syphon with full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. Maximum working pressure 10.0 bar. Cold water use only.

Section:: 2035 Cistern - Flushing
Section Subtitle:: Incorporating Type AG air gap, providing fluid category 3 backflow protection. Suitable for use in a WC suite. Additional tests will need to be performed if required to demonstrate Type AUK1 air gap.
WRAS Approval Number:: 2112907
Expiry date:: 31/12/2026
Size:: ½” BSP Male inlet connection.
Marking:: Cap of Syphon marked either ‘Cascade +’ or ‘Dudley Turbo’ Part 4 Inlet valve discharge cap marked ‘HYDROFLO’. Front nut of inlet valve marked ‘DUDLEY BS 1212/4’. Part 3 Inlet valve marked T. Dudley or BETA (brand of Thomas Dudley) & BS1212 part 3 on front face of back plate
Installation Requirements:: R001 R280 R556
Model:: Elite WC Cistern.
Manufacturer:: Thomas Dudley Ltd

Company Name
Thomas Dudley Ltd
Address
Dauntless Works PO Box 28 New Birmingham Road
Postcode
DY1 4SN
Phone
Tel: 0121 557 5411 Fax: 0121 557 5345

View All Listings by this Company

WRAS Approval Number: #2212904

Range of high and low level BS EN 14055 (2018) WC cisterns incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a dual flush or mono flush syphon for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres.. Maximum working pressure 10.0 bar. Cold water use only.

Section:: 2035 Cistern - Flushing
Section Subtitle:: Incorporating Type AG air gap, providing fluid category 3 backflow protection. Suitable for use in a WC suite. Additional tests will need to be performed if required to demonstrate Type AUK1 air gap.
WRAS Approval Number:: 2212904
Expiry date:: 31/12/2027
Note:: R560 applies to bottom entry models only
Size:: ½” BSP Male inlet connection
Marking:: Cap of Syphon marked either ‘Cascade +’ or ‘Dudley Turbo’ Part 3 Inlet valve marked T. Dudley or BETA (brand of Thomas Dudley) & BS1212 part 3 on front face of back plate
Installation Requirements:: R001 R280 R560 R556 R581
Model:: Trishell WC Cistern.
Manufacturer:: Thomas Dudley Ltd

Company Name
Thomas Dudley Ltd
Address
Dauntless Works PO Box 28 New Birmingham Road
Postcode
DY1 4SN
Phone
Tel: 0121 557 5411 Fax: 0121 557 5345

View All Listings by this Company