Caleffi S.p.A Approvals


#2007807

Solar range of auto air-vent valves (chromium plated brass) and a plastic float. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.

Section:
1980 Valves
Section Subtitle:
Air venting. Fittings in this section are suitable for above ground installations only.
WRAS Approval Number:
2007807
Expiry date:
31/07/2025
Size:
See model
Marking:
Caleffi Solar, max temp & max pressure on body. Caleffi logo on cap.
Installation Requirements:
R001 R200 R535
Model:
250031 – 3/8” BSP (M) 250131SD – 3/8” BSP (M) 250131VLL – 3/8” BSP (M) 250131 – 3/8” BSP (M) 250131HRM – 3/8” BSP (M) 250041A – ½” NPTF 250041 – ½” BSP (M) 250831 – 3/8” BSP (M) 250931 - 3/8” BSP (M) 250133 - 3/8” BSP (M)
Factor:
Caleffi S.p.A
Company Name
Caleffi S.p.A
Address
PLANT 2. S.R. 229 28010 Fontaneto d'Agogna (NO)
Phone
+39 0322 8491
General Email
info@caleffi.com

View All Listings by this Company

Print This Approval


#2009326

Range of pre-set (at 3.0 bar) pressure relief valves incorporating DZR brass bodies and an EPDM diaphragm. The valve is fitted with hand operated rotating easing gear. Maximum operating temperature 85°C.

Section:
2210 Valves
Section Subtitle:
Pressure relief.
WRAS Approval Number:
2009326
Expiry date:
30/09/2025
Note:
Closed circuit use only.
Size:
see model
Marking:
Caleffi logo, flow arrow, date of manufacture (MM/YY) & size on body. Pressure & temperature on cap. Some (but not all) models are marked with ‘CR.
Installation Requirements:
R001 R200
Model:
A312400 CST: 17.5mm manifold x ½” BSP (M). A312401 CST: 19.87mm manifold x ½” BSP (F). A312414 CST: 20mm manifold x ½” BSP (M). A312420 CST: 20mm manifold x 22mm compression. A312430 CST: ½” BSP manifold x ½” BSP (F). A312438 CST: 19.88mm manifold x ½” BSP (M). A312439 CST: fast fit manifold connection - 19.95mm. A314402 CST: 15mm manifold x ½” BSP (M). A314437 CST: ½” BSP (M) BSP x 15mm compression. A314402 BSC: 15mm manifold x ½” BSP (M).
Manufacturer:
Caleffi S.p.A
Company Name
Caleffi S.p.A
Address
PLANT 2. S.R. 229 28010 Fontaneto d'Agogna (NO)
Phone
+39 0322 8491

View All Listings by this Company

Print This Approval


#2007376

Cold water inlet control group with a DZR brass body consisting of a pressure reducing valve, (adjustable between 2.7 and 3.3 bar, but factory set at 3.0 bar), a stainless steel strainer and a plastic bodied pressure relief valve (pre-set at 8.0 bar). The product incorporates a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The pressure relief valve is fitted with a rotary type easing gear. Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C.

Section:
2345 Valves
Section Subtitle:
Special combination assemblies.
WRAS Approval Number:
2007376
Expiry date:
31/07/2025
Size:
22mm compression
Marking:
Caleffi, CR and flow arrow on body.
Installation Requirements:
R001 R120
Model:
533121H CST
Manufacturer:
Caleffi S.p.A
Company Name
Caleffi S.p.A
Address
PLANT 2. S.R. 229 28010 Fontaneto d'Agogna (NO)
Phone
+39 0322 8491

View All Listings by this Company

Print This Approval


#2009331

Range of indirect heat interface units providing heating and instantaneous hot water. The hot water and space heating is provided via two separate plate heat exchangers. The space heating circuit incorporates an expansion vessel and expansion relief valve (set @ 3.0 bar). The primary circuit only is supplied with isolation valves on the flow and return. Maximum working pressure primary 16.0 bar. Maximum working pressure space heating 2.5 bar. Maximum working pressure secondary hot water (DHW) 10.0 bar. Maximum operating temperature primary 75°C. Maximum operating temperature space heating 85°C. Maximum operating temperature secondary hot water (DHW) 65°C.

Section:
1350 Heat Exchangers
WRAS Approval Number:
2009331
Expiry date:
30/09/2025
Note:
Not supplied with a temporary filling loop. The filling loop must be installed with the appropriate backflow prevention device in accordance with clause G24.2, Guidance to the Water Supply (Water Fittings) Regulations 1999.
Size:
Primary: 1” BSP (M). Secondary: ¾” BSP (M). DHW: ½” BSP (M).
Marking:
Caleffi on cover. Pressure, model, temperature and other technical information on inside cover.
Installation Requirements:
R001 R360
Model:
SATK30105 - 75kW - Indirect HIU. SATK30103 - 50kW - Indirect HIU.
Manufacturer:
Caleffi S.p.A
Company Name
Caleffi S.p.A
Address
PLANT 2. S.R. 229 28010 Fontaneto d'Agogna (NO)
Phone
+39 0322 8491

View All Listings by this Company

Print This Approval


#2012308

Filling loop assembly, consisting of a stainless steel braided EPDM lined flexible hose, a lever operated brass spherical valve and a DZR brass double check valve assembly that incorporates a lever operated spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 23°C.

Section:
1015 Filling Loop
WRAS Approval Number:
2012308
Expiry date:
31/12/2025
Size:
15mm compression
Marking:
Caleffi logo, CR, and flow arrow on mould on double check valve assembly body Caleffi logo mould on isolation valve body
Installation Requirements:
R001
Model:
300600 300600 CST
Manufacturer:
Caleffi S.p.A
Company Name
Caleffi S.p.A
Address
PLANT 2. S.R. 229 28010 Fontaneto d'Agogna (NO)
Phone
+39 0322 8491

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 5 of 13

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.