Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Jotapipe IL 6001-120S'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS dated 22nd August 2018. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL Ordinary Portland Cement'. Factory applied cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 27 days@20-25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL Portland Blast Furnace Slag Cement'. Factory applied cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 27 days@20-25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Deep Seal Liquid Epoxy Paint'. Factory applied, two-component epoxy paint consisting of a base and activator, available in red/brown, grey, blue & white colours. Mix base and activator in a volume ratio of 3:1. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-201'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Zhenxin Epoxy Powder Coating'. Factory applied, blue coloured epoxy powder coating. Apply as per product instructions 'File No. ZX-9-HY/NG' dated '2019-6-2'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyester Blue 5010 High Gloss-207770501000'. Factory applied, blue coloured polyester powder coating. Apply as per TDS for 'Series 7000 Polyester Powders', issue ref. '09-8637555', updated '5/17'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaguard CSF 585'. Factory applied, light blue coloured two component epoxy coating consisting of a base and hardener. Mix base & hardener in a volume ratio of 77.5:22.5. Cure for 15 days@21°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempadur 35560 Cream Coating with Hempadur 15590 Red Primer'. Factory applied, cream coloured, two-component epoxy coating for use with epoxy primer. ‘Hempadur 15590 Red Primer’ is a two-component primer which is mixed in a 15:4 volume ratio and can be cured for 16 hours@20°C or 4 days@20°C. 'Hempadur 35560 Cream’ is a two-component coating which is mixed in a 6.8:2 volume ratio and then cured for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELECTROLINE ES 1212'. Factory applied, white coloured, two-component, solvent -free epoxy coating. Mix base and hardener in a 2:1 volume ratio. Cure for 7 days@28°C - 30°C. From August 2019 to October 2022 the coating is for use with water up to 23°C. From November 2022 to August 2024 the coating is for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'EVER CM-2'. Factory applied, grey coloured cement mortar. Mix, apply and cure in accordance with manufacturer's safety data sheet '2019-02-19 revision A1'. For use with water up to 65°C.
'Fluiglide E'. Factory applied, two-part, white coloured epoxy coating consisting of a base and activator. Mix base and activator in a mass ratio of 2:1. Cure coat 1 for 4 hours@20°C. Cure coat 2 for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LUBERPOX-2K-SEALCOAT'. Factory applied, two component epoxy coating consisting of a base (IV16) and hardener (IW16). Mix and apply as per Technical Data Sheet ‘LP/HF’, rev. 1 dated 22.07.2018. Cure for 20 minutes@22°C and then 40 minutes@75°C. For use with water up to 65°C.
'Electrocement type CEM III A'. Factory applied, grey coloured slag cement mortar, intended to line ductile iron pipes and fittings. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22. Cure for 28 days at 20°C - 22°C OR 24 hours@27°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL Sulphate Resistant Portland Cement'. Factory applied, grey coloured cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 27 days@ between 20°C and 25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix & cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fontezinc HR'. Factory applied, grey coloured, two-component, inorganic zinc silicate coating. Mix the two parts in accordance with product data sheet '30.10.2018'. Cure for 30 minutes@20-21°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER CM-2'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a weight ratio of 1:2:0.4. Cure at ambient temperature for 4 hours and then vapour cure for 6 hours@55°C. For use with water up to 65°C.
'EP-I-101'. Factory applied, white coloured epoxy powder coating. Apply as per manufacturer's user manual dated '22/04/2019', revision '1.0'. Cure for 10 minutes@200°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BFSC PAM SDN 1'. Factory applied, grey coloured blast furnace slag cement mortar/admixture. Mix sand and cement in a 1.63:1 mass ratio. Add water in a water/cement mass ratio of 0.25:1. Add admixture in an admixture/cement mass ratio of 0.0006. Cure for 5 hours at 70°C (at a rate of 17°C/hour up to 70°C, then holding at 70°C for 1 hour). For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Rashmi Blast Furnace Slag Cement Mortar'. Factory applied, grey coloured, blast furnace slag cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.6. Cure for 120 minutes@50°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Page 1 of 24
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
