Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Pulron 101 Aqua'. Factory applied, blue coloured PE coating. Apply as per manufacturer's instructions application guide dated 07.02.2018. Cure for 10 minutes@200°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Rashmi Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Rashmi Portland Slag Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘JSW Portland Slag Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
18530 KANEPOX LINING FREE PRO Cream, Oxide Red & Blue'. Factory applied, two-component epoxy coatings available in cream, red and blue colours. Mix part A & B in a volume ratio of 2:1. Cure for 7 days@25°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epigard Solvent Free Epoxy Finish'. Factory applied, two-component, red coloured epoxy coating. Mix base & accelerator in a volume ratio of 3:1. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing and mixing conditions that appear on the approval. If the cure/mix conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SOLID-01'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APCODUR CP 683 primer for use with APCOGUARD SF 155'. 'APCODUR CP 683 primer’ is a two-component primer. Mix base and hardener in a 3:1 volume ratio and then cure for 24 hours@28-30°C. ‘APCOGUARD SF 155' is a two-component top-coat. Mix base and hardener in a 4:1 volume ratio and then cure for 10 days@28-30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 6 of 47
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
