Heaters

Section Code 1360 : Electric instantaneous, mains fed, closed outlet. Heat retained in instantaneous water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

Back To Directory Sections

WRAS Approval Number: 1609083

Range of instantaneous water heaters with plastic bodies and EPDM O-rings. The heater inlet incorporates a flow regulator, a check valve cartridge suitable for backflow protection against Fluid Category 2) and a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

  • Section: 1360 Heaters
  • Section Subtitle: Electric instantaneous, mains fed, closed outlet. Heat retained in instantaneous water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
  • WRAS Approval Number: 1609083
  • Expiry date: 30/09/2021
  • Size: ½” BSP male inlet/outlet
  • Marking: Zip Inline on front cover. Model on adhesive label at bottom of unit
  • Installation Requirements R001
  • Model
    CEX-O (over sink). CEX-U (under sink).
  • Factor: Zip Heaters (UK) Ltd.
    Company Name
    Zip Heaters (UK) Ltd.
    View All Listings by this Company
  • Manufacturer: Clage GmbH
    Company Name
    Clage GmbH
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1704701

Instantaneous main fed water heaters with plastic body with EPDM rubber and silicone rubber O-rings and seals, and fibre gaskets. The heater incorporates a single check valve cartridge (suitable for backflow protection against Fluid Category 2). The inlet incorporates a spherical valve including stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

  • Section: 1360 Heaters
  • Section Subtitle: Electric instantaneous, mains fed, closed outlet. Heat retained in instantaneous water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
  • WRAS Approval Number: 1704701
  • Expiry date: 30/04/2022
  • Size: ½” BSP captive nut inlet and outlet
  • Marking: Zip InLine on front cover. Product information inside cover.
  • Installation Requirements R001
  • Model
    DEX12 (12kW), DEX18-27 (Can be selected for 18, 21, 24 or 27kW on installation), DBX18 (18kW), DBX21 (21kW), DBX24 (24kW) & DBX27 (27kW).
  • Factor: Zip Water UK
    Company Name
    Zip Water UK
    View All Listings by this Company
  • Manufacturer: Clage GmbH
    Company Name
    Clage GmbH
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 2003355

Electric instantaneous main fed water heaters with stainless steel bodies, EPDM O-rings, silicone seal (40132212 model only), and fibre gaskets. The heaters are supplied with an inlet safety control group consisting of a pressure reducing valve (adjustable between 2.7 and 3.3 bar), pre-set expansion relief valve set at 6.0 bar, a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) and an expansion vessel. They are also supplied with a stainless steel braided PEX lined flexible hose assembly incorporating ½” and ⅜” captive nut end connections, and ⅜” BSP (M) brass equal tee for installation prior to the inlet safety control group. The outlet arrangement on the 40132212 model only combines the near boiling water outlet and cold inlet supply via a thermostatic mixing valve, as well as a separate outlet for near boiling water. The outlet arrangement of the 40132312 model supplies near boiling water. The products are supplied with a tundish for installation on the outlet of the safety relief valve. Maximum inlet supply pressure to inlet safety control group 10.0 bar. Maximum working pressure 5.5 bar. Cold supply (inlet). Maximum operating temperature 99°C (water heater and near boiling outlet both models), 90°C (for hot water outlet via thermostatic mixing valve 40132212 model only).

  • Section: 1360 Heaters
  • Section Subtitle: Electric instantaneous, mains fed, closed outlet. Heat retained in instantaneous water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
  • WRAS Approval Number: 2003355
  • Expiry date: 31/03/2025
  • Note: Expansion vessels should be installed in the vertical orientation and located so that the length of the connecting pipework is kept to a minimum. Discharge to drain must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.
  • Size: ⅜” BSP (M) (to tee piece). Stainless steel braided PEX lined flexible hose assembly incorporating ½” captive nut end connection (to boiler unit).
  • Marking: HotSpot logo, serial number and date of manufacture YYWW followed by a unique number, e.g. 1923001. (19 = 2019, 23 = week 23, 001 = unique production no.) on adhesive label on body.
  • Installation Requirements R001 R007 R009 R511
  • Model
    40132312 Hotspot Titanium 4L boiler. 40132212 Hotspot Titanium 8L boiler.
  • Factor: HotSpot Titanium UK Ltd
    Company Name
    HotSpot Titanium UK Ltd
    View All Listings by this Company
  • Manufacturer: Inventum Industrial BV and Inventum Technologies BV
    Company Name
    Inventum Industrial BV and Inventum Technologies BV
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 2007344

Range of ‘HYCO’ electric instantaneous water heaters with plastic bodies, NBR and silicone ‘O’-rings. The inlet of model IN96T incorporates a plastic strainer. Maximum working pressure 7.5 bar. Maximum operating temperature 60°C.

  • Section: 1360 Heaters
  • Section Subtitle: Electric instantaneous, mains fed, closed outlet. Heat retained in instantaneous water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
  • WRAS Approval Number: 2007344
  • Expiry date: 31/07/2025
  • Size: ½” BSP male inlet/outlet
  • Marking: Hyco, serial number, model, manufacturer, address, contact No, product code and other technical information side of unit.
  • Installation Requirements R001
  • Model
    IN44T, IN60T, IN96T, IN44 & IN60.
  • Manufacturer: Hyco Manufacturing Ltd
    Company Name
    Hyco Manufacturing Ltd
    View All Listings by this Company

Print This Approval


Show Per Page
5102050Show All

Back To Directory Sections

Page of