Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'MEKCOAT Liquid Membrane Coating'. Factory applied, two-component, blue coloured polyurethane coating. Mix in a 1:1 volume ratio. Cure for 24 hours@23-24°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'5017 Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions issued January 2020, 'V7.2'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JH'. Factory applied, blue coloured epoxy powder coating. Heat substrate to 220°C for 30 minutes, spray apply coating and then cure at 190°C for 20 minutes. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the cure and/or application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EUROKOTE® 46-20’. Factory applied, red-brown coloured, two-part epoxy resin coating. Mix and apply as per manufacturer's technical data sheet 'Doc. 087' dated 01/07/2011. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Electroline ES 1212-Black`. Factory applied, black coloured, 2 part epoxy coating. Mix parts A&B in a 3:1 volume ratio. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘SIGMAPRIME 200 for use with SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. SIGMAPRIME 200 (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio. Cure for 3 days@23°C. SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue) is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio. Cure for 12 days@23°C. For use with water up to 23°C.
`R2 Red & R2 Blue`. Factory applied epoxy powder coatings manufactured in Changzhou. Apply as per manufacturer's instructions for use 'ANCZ-RAD-W501', 'revision no: 2' dated 'May. 5th 2021'. Cure for 10 minutes@200°C. For use with water up to 80°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001 Blue`, factory applied, blue coloured, fusion bonded epoxy coating. 'Jotaguard VA 5001 Red`, factory applied, red coloured, fusion bonded epoxy coating was added to the approval in June 2023. Apply both coatings as per Jotun Technical Data Sheet issued 9th November 2015. Cure for 5 minutes@245°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Kubota sulphate-resisting Portland cement'. Factory applied, grey coloured cement. Mix sand, cement and water in a mass ratio of 1:2.5:0.4. Cure for 24 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Kubotapowder TK1413F'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions 'GR-294E' dated 2018/10/01. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 9 of 51
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
