Water Regulations Approval Scheme Ltd

Directory Search Results

WRAS Approval Number: #2307539

'ProWarm PERTAL'. White coloured, extruded PE-RT/Al/PE-RT pipe. For use with water up to 65°C.

Section:: 5240 Polyethylene
Section Subtitle:: Components. All components listed in this section have been tested for water contact suitability of material only.
WRAS Approval Number:: 2307539
Expiry date:: 31/07/2028

Approval Holder:: The Underfloor Heating Store Limited

Company Name
The Underfloor Heating Store Limited
Address
Highbourne House, Eldon Way, Crick Industrial Estate, Crick, Northampton
Postcode
NN6 7SL

View All Listings by this Company

WRAS Approval Number: #2311515

‘LURANYL® KR 2402 TW 35061, LURANYL® KR 2403 G4 TW 26343 & LURANYL® KR 2403 G6 TW 26343’. polyphenyleneoxide/polystyrene. In May 2025, ‘LURANYL® KR 2403 G2 TW GY4090-24’ & ‘LURANYL® KR 2403 G6 TW GY4040-24’, dark grey coloured, injection moulded polyphenyleneoxide/polystyrene materials were added to the approval. In November 2025, ‘LURANYL® KR 2403 G2 TW 26343’, black coloured, injection moulded polyphenyleneoxide/polystyrene material was added to the approval. All grades are for use with water up to 85°C.

Section:: 5250 Polyphenyleneoxide (PPO)
Section Subtitle:: Material only. Components made from materials listed in this section may be required to be submitted for audit tests.
WRAS Approval Number:: 2311515
Expiry date:: 30/11/2028

Approval Holder:: Romira GmbH

Company Name
Romira GmbH
Address
Siemensstrasse 1-3, D-25421 Pinneberg
Country
Germany
Phone
+49 (0)4101-706 304
General Email
info@romira.de

View All Listings by this Company

WRAS Approval Number: #2310559

'Chemfix 100'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions ref. no. 'rev5' dated 04/06/218. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:: 5311 Resin Anchors
Expiry date:: 31/10/2028

Approval Holder:: Chemfix Products Ltd.

Company Name
Chemfix Products Ltd.
Address
Mill Street East, Dewsbury, West Yorkshire
Postcode
WF12 9BQ
Phone
+44(0)1924 453886

View All Listings by this Company

WRAS Approval Number: #2311521

'EPDM 70.502-03 washers & 'O' rings'. Black coloured, injection moulded EPDM washers and 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.5 and 2.6mm. For use with water up to 85°C.

Section:: 5360 Rubbers
Section Subtitle:: Ethylene Propylene Diene Monomer (EPDM) - components.
WRAS Approval Number:: 2311521
Expiry date:: 30/11/2028

Approval Holder:: Angst+Pfister AG

Company Name
Angst+Pfister AG
Address
Thurgauerstrass 66, CH8052 Zurich
Country
Switzerland
Phone
+41 44 306 61 11
General Email
ch@angst-pfister.com

View All Listings by this Company

WRAS Approval Number: #2309538

'PT0165/2'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius 1.25mm. For use with water up to 85°C.

Section:: 5365 Rubbers
Section Subtitle:: Ethylene Propylene Diene Monomer (EPDM) - material only. Components made from materials listed in this section may be required to be submitted for audit tests.
WRAS Approval Number:: 2309538
Expiry date:: 30/09/2028

Approval Holder:: TS International S.r.l.

Company Name
TS International S.r.l.
Address
Via G. Carducci 19, 24060 Sovere (BG)
Country
Italy

View All Listings by this Company