'Silicone LSR2090-50'. Colourless (translucent), injection moulded silicone rubber material. Shore hardness 50. Tested in-radius size between 0.25mm & 3.5mm. For use with water up to 85°C.
'Loctite EA 9480'. Site applied, two-component, white coloured (once mixed) epoxy adhesive. Mix and apply as per manufacturer's technical data sheet dated October 2014. Cure for 7 days@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Novodur® SBM-90 Q203'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
'Novodur® SBM-90'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
Deck mounted single hole, single outlet (fixed) electronically controlled tap assembly (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Tempearture is controlled from a separate control unit incorporating a thermostatic cartridge, which is operated by a single lever on the side of the unit. The spout connects to the unit via a (transparent) PEX-b pipe. The inlets of the control unit incorporate a stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the unit incorporates a plastic flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose incorporates an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns with a side entry BS 1212-4(2016) float operated inlet valve providing a type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two button assembly for a 6 or 3 litre flush volume. The cistern incorporates a servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. Maximum working pressure 10.0 Bar, Cold Water use only
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only. .
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC
Range of non-verifiable double check valve assemblies (DZR brass bodies) incorporating spherical valves and either red or blue butterfly handles. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body (chrome plated or brass finish) with a port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc and cartridge headworks with plastic bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
A range of ceramic cartridge headworks with plastic bodies incorporating EPDM `O`-rings and seals for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of quarter turn ceramic disc headworks with brass bodies (various finishes on the stem), silicone seals, and EPDM ‘O’-rings for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Thermostatic cartridge incorporating brass body (chrome plated), stainless steel strainers and EPDM ‘O’-rings. For insertion into specifically dimensioned tap bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of thermostatic cartridges incorporating plastic bodies, stainless steel filters and EPDM ‘O’-rings. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 75 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
