Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections‘PRIMER NATZINC EP9015 SC PART A’ Primer for use with ' HYDRALFUN AC BLEU PAM RAL5005-CZL8190 ' top-coat. Factory applied, blue coloured (once applied) primer and finish-coat. Mix base:hardener of primer in a 100:10 weight ratio and apply as per manufacturer’s TDS February 2024. Then apply top-coat as per manufacturer’s TDS February 2024. Cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempathane PW 35660 blue & off-white`. Factory applied, two-component polyurethane liquid coating consisting of a base and curing agent. Mix base and curing agent in a 3:1 volume ratio and apply as per product data sheet dated December 2023. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Transpoxy Guard 472'. Factory applied, two-part, creamy white coloured epoxy resin coating. Mix base and hardener in a mass ratio of 4:1 and apply as per manufacturer's TDS dated 'January 2017'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM Sulphate Resisting Cement'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1.0:2.0:0.4 weight ratio and apply as per manufacturer's TDS '004', dated '2023.02.01'. Air cure for 4 hours at 23°C and the vapour cure for 6 hours at 60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM5 Blast Furnace Slag Cement'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1.0:2.0:0.4 weight ratio and apply as per manufacturer's TDS '002', dated '2023.02.01'. Air cure for 4 hours at 23°C and the vapour cure for 6 hours at 60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikafloor® P 649 and Sikalastic® M 649 Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply Sikafloor® P 649 primer as per Product Data Sheet ‘MBS_CC-UAE/Sl_P_649_04_24’. Cure for 2 hours@25°C. Then mix and apply Sikalastic® M 649 Coating as per Product Data Sheet ‘MBS_CC-UAE/Sl_M_649_06_21/v3/01_24/v4/03_24’. Cure for 1 minute@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PM6/35/7153'. Factory applied, grey coloured enamel coating. Apply as per manufacturer's data sheet RTU version '01-2018'. Cure for 8 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'PP8000 M62091'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's data sheet version '01-2018'. Cure for 7 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'JERLAC Solventless Epoxy Grey'. Factory applied, grey coloured, two-component Epoxy coating. Mix Base:Curing Agent in a 2:1 volume ratio and apply as per manufacturer's TDS reference 'BN434', dated '24/07/2023', revision '00'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Wanan brand WA F 501'. Factory applied, blue coloured epoxy powder coating. Apply as per 'Wanan Industry Group Co., Ltd.' TDS 'WATDS20200801a' dated 'Aug. 1, 2020'. Cure for 20 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E0-850-5210-001'. Factory applied, blue coloured epoxy powder coating. Apply as per 'Ziac Trattamenti Metallici SNC' instructions 'nr.01, rev.00, issue 01' dated 01/082016. Cure for 30 minutes@210°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS 520B'. Factory applied, dark grey coloured enamel coating. Apply as per manufacturer's instructions 'ref. PRO PR 15 Gi 01 UK' dated April 04, 2024. Cure for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HYDRALFUN AC BLEU PAM RAL5005-CZL8190'. Factory applied, blue coloured acrylic paint. Apply as per manufacturer's TDS dated February 2024. Cure for 21 days@23°C. Between April 2024 and July 2024, the paint is for use with water up to 50°C. From August 2024 the paint is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HYDRALFUN AC NOIR PAM - CZL8579'. Factory applied, black coloured acrylic paint. Apply as per manufacturer's TDS dated July 2018. Cure for 21 days@23°C. For use with water up to 60°C.
'NAVCOAT-001 HT'. Factory applied, black coloured bitumen based paint. Apply as per manufacturer's data sheet 'NCB/001', issue date '12.07.2023'. Cure 7 days@30°C. For use with water up to 60°C.
'Loctite EA 109'. Factory applied, grey/beige coloured, heat cured epoxy coating. Apply as per manufacturer's TDS for Loctite ESP109 (product has changed name) dated July 2007. Cure for 2 hours@130°C. For use with water up to 85°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Loctite PC 7255 GN (Green) coating for use with Bonderite M-NT 1455-W primer'. Factory applied, green coloured, two-component epoxy resin coating. In June 2025 ‘LOCTITE PC 7255 GY (Grey) coating for use with BONDERITE M-NT 1455 Primer-W Coating’ was added to the approval. Factory applied, grey coloured, two-component epoxy resin coating. Prime the surface to be coated with the Bonderite primer wipe. Mix and apply as per manufacturer’s TDS dated October 2016. Cure for 7 days@23°C at 45% relative humidity. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Balinit Milubia'. Factory applied, dark grey coloured, two layered coating system consisting of a titanium bottom layer & diamond like coating top layer. Apply as per manufacturer`s instructions '080224' dated 08-Feb-2024. No curing required. For use with water up to 85°C.
‘Endoprene® 85-20’. Factory applied, two component, beige coloured, solvent free polyurethane coating. Mix and apply as per Technical Data Sheet dated '09/09/2019'. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Zhenxin Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HY/NG' dated '2023-06-02'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PM6/35/7623 Vitreous Enamel Coating. Factory applied, blue coloured enamel coating. Apply and fire as per manufacturer's datasheet dated '01-2018' For use with water up to 85°C.
'18521 Kanepox Lining Free Blue for use with Kanepox Hardener 0362'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix 18521 Kanepox Lining Free Blue & Kanepox Hardener 0362 in a 3.5:1 volume ratio and apply as per manufacturer's datasheet ‘Rev. No. 11’ dated February 2018. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MY-5005'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's user manual 'rev: 1.0' dated 01/01/2018. For use with water up to 85°C.
'Jotapipe IL 6001-120S'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS dated 22nd August 2018. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Edelpoxy FN TM 142'. Factory coloured, red coloured epoxy resin coating consisting of a base and hardener. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's IFU 'PCC/ PC 142', dated '10.07.2018'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VPC5015 Sky Blue FBE'. Factory applied, blue coloured fusion bonded, epoxy powder coating. Pre-heat the surface to be coated to 200°C for 5 minutes and dip in a fluidised bed of powder coating as per manufacturer's data sheet 'VPC5015, revision 5' dated '25 January 2023'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaguard CSF 585'. Factory applied, light blue coloured two component epoxy coating consisting of a base and hardener. Mix base & hardener in a volume ratio of 77.5:22.5 and apply as manufacturer's Product Data Sheet '7785', revised May 31, 2022. Cure for 15 days@21°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaline 523'. Factory applied, two-component, yellow coloured or red/brown coloured epoxy coatings. Mix and apply in accordance with Product Data Sheet ref. 7623 dated February 4, 2021. Cure for 3 days@23°C. The red-brown coloured coating is for use with water up to 60°C. Between June 2024 and March 2025, the yellow-coloured coating is for use with water up to 23°C. Between April 2025 and June 2029, the yellow-coloured coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS EPX-02 Solvent Free Epoxy Coating and Hardener'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix coating & hardener in a 3.5:1 volume ratio and apply as per manufacturer's painting instructions 'Document Code 30', 'Rev No 7', dated '01.09.2018'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Luberpox-2K-DS-Lackfarbe IV17'. Factory applied, blue coloured, two-component epoxy coating. Mix coating and hardener in a weight ratio of 4:1 or volume ratio of 3:1 and apply as per manufacturer's TDS '01 – 11.06.2024'. Cure for 7 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Truform Cement OPC 43 Grade'. Factory applied, grey coloured cement. Mix cement:sand in a weight ratio of 2:1 and add 0.5 litres of water. Apply as per manufacturer's instructions 'TTPL/SOP/MCD/03', revision '00', dated 01.04.2018. Cure for 24 hours@27°C followed by 7 days@85°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Witcoat SF Epoxy Red Primer. Factory applied, red coloured, two-component epoxy primer. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's data sheet '15.09.2023 Rev No.: 00'. Cure for 7 days@30°C. For use with water up to 50°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix & cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SIGMACOVER 280 (Yellow/Green) + SIGMAGUARD CSF 650 (Green)'. Factory applied, light green coloured (once applied), epoxy primer & coating. Mix base and hardener of SIGMACOVER 280 in a 4:1 volume ratio and apply as per manufacturer's PDS '7417', dated 'May 23 2024'. Cure for 24 hours@20°C. Mix base and hardener of SIGMAGUARD CSF 650 in an 80:20 volume ratio and apply as per manufacturer's PDS '7443', dated 'July 26, 2022'. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI.Hygienic HI-Build Epoxy'. Factory applied, two- component, blue coloured epoxy coating. Mix base and hardener in a weight ratio of 100:15 and apply as per manufacturer's instructions 'LMIEP1403032', dated '22/06/2024'. Cure for 2 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELECTROLINE ES 1212'. Factory applied, white coloured, two-component, solvent -free epoxy coating. Mix base and hardener in a 2:1 volume ratio and apply as per manufacturer's TDS 'ECL/ TDS / ES1212', issue date '2-Feb-14', version '0'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'H-453'. Factory applied, grey coloured ceramic epoxy coating. Apply as per manufacturer's Technical Data Sheet 'TWJ-H-453', 'Edition A1', dated '01/12/2023'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Purethane NXT. Factory applied, off-white coloured, two-component Polyurethane coating. Mix resin and activator in a 2.5:1 volume ratio and apply as per manufacturer's 'APP-CA-NXT-Rev 04', dated '01.04.2023'. Cure for 7 days@23°C. For use with water up to 35°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Deep Seal Liquid Epoxy Paint'. Factory applied, two-component epoxy paint available in red/brown, grey, blue & white colours. Mix base and activator in a volume ratio of 3:1 and apply as per manufacturer's instructions 'DI/FG/2024/056', dated '25/04/2024'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Alesta Vanguard Blue Epoxy Powder EE80005001723’. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer’s TDS version '22/01/2015'. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement type CEM III A'. Factory applied, grey coloured slag cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', issue '04', rev. '0', dated '22.08.2024'. Cure for 28 days at 20°C - 22°C OR 24 hours@27°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Cicoprime®25 Primer and Cicoshield®PW100 Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply Cicoprime®25 Primer in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated October 2023. Cure for 2 hours@25°C. Then mix Cicoshield®PW100 Coating in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated August 2024. Cure for 1 minute@25°C. For use with water up to 85°C.
'61300 EPOXY TB BT BLEU 5005'. Factory applied, blue coloured epoxy powder coating. Spray apply as per manufacturers TDS dated '15/2/2019'. Cure for 20 minutes@160°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS-FBE-Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS 'Document Code 53', 'Publication No 5', dated 01.03.2024. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BFSC Foug SDN’. Factory applied, grey coloured, blast furnace slag cement intended to line pipes. Mix sand and cement in a mass ratio of 1.5:1, then add water in a water/cement mass ratio of 0.36:1 and apply as manufacturer's instructions. Cure for 48 hours@23°C, 70% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ARC SD4i(E)'. Factory applied, grey and blue coloured, two-part epoxy coatings. Mix parts A and B in a weight ratio of 2.5:1 and apply as per manufacturer's Application Instructions 'EN-085034EU', dated '01/2025'. Cure for 72 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ARC 858(E)'. Factory applied, dark grey coloured, two-part epoxy coating. Mix parts A and B in a weight ratio of 4:1 and apply as per manufacturer's Application Instructions 'EN-085013EU', dated '08/2024'. Cure for 54 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ENDOPRENE® 851 Blanc'. Factory applied, white coloured, two-component polyurethane coating. Mix parts A & B in 50:50 volume ratio and apply as per manufacturer's TDS dated 10/07/2024. Cure for 6 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'175-767 Polyester blue 5012'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions updated '15.03.2018'. Cure for 10 minutes@180°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Series 2000 RAL 5015'. Factory applied, blue coloured epoxy resin coating. Apply as per manufacturer’s data application sheet ‘Revision: 6 (2018/10/01)’ created ‘2015/11/11’. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 8 of 11
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
