Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. The product incorporates stainless steel or nylon braided EPDM connection hoses. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of carbon filter cartridges. Cold water use only.
‘APL’ & 'AP' ranges of brass press fittings for use with ‘APE Multylayer' pipe. Connection is achieved via TH or U profile press jaws. AP range, only TH profile; APL range, TH and H profile; TH and H profile from DN 16 to DN32; TH for DN40, DN50 and DN63. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “VMA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of stainless steel press fittings to be used with stainless steel pipes. Connection is achieved via M profile press jaws. For above ground and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Instantor range of copper press fittings with an EPDM ‘O’-ring for use with copper pipe to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass press fittings with EPDM ‘O’-rings for use with Rifeng B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of stainless-steel press fittings for use with stainless steel pipe. Above ground use only. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of stainless-steel press fittings with EPDM ‘O’-rings and EPDM washers. For use with stainless-steel pipe. Joints are achieved using a press fitting tool. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
‘ZL’ range of U profile press fittings (nickel plated brass bodies) for use with ‘ZL’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of copper solder ring fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of compression fittings with brass or nickel plated brass for use with copper pipe (manufactured to EN 1057). Above ground use only for use. Max working pressure 16 bar. Max operating temperature 85°C
Range of brass fittings with compression connections to be used with copper pipes EN 1057. For above ground use only. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
‘Universal Transition Coupling (UTC)’ range of plastic compression fittings for use with the following pipe types and sizes: Stainless steel (manufactured to ASTM A554/ BS EN 10312): ¾”, 1” & 1¼”. Galvanised (EN 10255): ¾”, 1”, 1¼”, 1½” & 2”. Copper (BS EN 1057): 15mm, 22mm & 28mm. PVC (BS EN 1452): 20mm & 2”. ABS (BS 5391-1): 20mm, 25mm & 32mm. PE80 & PE100 pipe (to BS EN 12201): 20mm, 25mm, 32mm, 50mm & 63mm. For use above and below ground. Maximum working pressure 12.5 bar. Cold water use only.
Range of brass press fittings for use with copper pipe (manufactured to EN1057:2006 and +A1:2010 Seamless round copper tube, R250 half hard). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of DZR brass push fit fittings for use with copper pipe (EN1057). Maximum working pressure 10.0 Bar. Maximum operating temperature 65 °C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of water meters with brass bodies and plastic turbines. The inlet incorporates a plastic filter. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Ranges of sensor operated flow control devices either mains or battery powered, incorporating a normally closed solenoid valve to control the flow and operated via an infra-red sensor. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8 Bar Maximum operating temperature 65°C
Range of ‘Tcontrols’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
Range of multistage centrifugal pumps with stainless steel impellers, intermediate chambers, shaft and outer sleeve. The Movitec VME models and VE/VSE models added May 2025 can also incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressures: Existing models: Comeo C models 10.0 bar, Movitec VM models with an oval flange or VME models with integral check valve 16.0 bar, All other Movitec VM models 25.0 bar. Models added May 2025: Movitec V/VS models with an oval flange or VE models with integral check valve 16.0 bar, All other Movitec V/VS models and Movitec HI/HSI models 25.0 bar. Maximum operating temperatures: Existing models: Comeo C and Movitec VME models with integral check valve 60°C, all other model variants 100°C. Models added May 2025: Movitec VE models with integral check valve 60°C, all other model variants 100°C.
Range of single and twin ended shower booster pumps with plastic bodies and plastic impellers. The inlets/outlets incorporate stainless steel braided EPDM lined flexible hose assemblies with isolation valves and stainless-steel strainers. The outlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. The Universal Twin models incorporate an expansion vessel. Maximum working pressure 1.5, 1.8, 2.0, 2.5, 2.6, 3.0 Bar (see model for more details). Maximum operating temperature: 60.0°C.
Range of wall and ceiling mounted overhead shower outlets, (plastic bodies – various finishes). Both models incorporate a built-in pressure regulator. Maximum operating temperature 85°C. Open outlet use only
Range of shower outlets, (plastic bodies - chrome plated) incorporating a plastic flow regulator. Products 24 540 xx0, 24 541 xx0, 24 550 xx0, 24 551 xx0 to be installed together with 24 573 180 Hansgrohe Raindance Alive Basic set. Maximum operating temperature 60°C. Open outlet use only.
Range of chrome plated plastic shower handsets. Maximum operating temperature: 65°C Open outlet use only.
Range of wall mounted brass shower outlets in various finishes. Open outlet use only. Maximum operating temperature: 65°C
Range of Y patterned strainers with a brass body. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pressure sensors with stainless steel bodies. Models consist of a sensor and male threaded end. Maximum working pressure: See Models. Maximum operating temperature 90°C.
Range of shower hoses with PVC outer (various finishes) and TPE liner. Maximum operating temperature 65.0°C. Open outlet use only.
Range of stainless steel or nylon braided, PEX lined flexible hose assemblies with various brass end connections. Maximum working pressure 10.0 Bar. Maximum operating temperature 85 °C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections. Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
temperature and pressure relief valve set at 7.0 bar@90˚C. A safety kit (manifold) consisting of a check valve cartridge (verified by test, suitable for backflow protection against Fluid category 2) strainer, an expansion relief valve set at 6.0 bar and pressure reducing valve set at 3.0 bar. A tundish, expansion vessel and a filling loop assembly, incorporating a stainless steel braided EPDM lined flexible hose, brass bodied isolation valve and a DZR brass non-verifiable double check valve assembly that incorporates an isolation valve. Maximum working pressures: Secondary circuit 5.5 bar. Primary circuit 3.0 bar Maximum operating temperature 90.0°C
Range of wall mounted thermostatic bar shower mixers ((brass bodies - various finishes), incorporating a quarter turn ceramic disc headwork controlling the flow with single lever type operating members. The temperature is controlled independently via a thermostatic cartridge with single lever type operating members. Models come with either 2,3 or 4 push type headworks for different functions. The inlet incorporates approved single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides backflow protection). Products are supplied with a shower handset, shower hose. The products need to be installed in combination with a specific basic set. 12 571 xx0= 18310180 Basic set for thermostatic module Select for 2 functions (WRAS 2207061) 12 572 xx0= 18311180 Basic set for thermostatic module Select for 3 functions (WRAS 2207061) 12 573 xx0= 18312180 Basic set for thermostatic module Select for 4 functions (WRAS 2207061) Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of thermostatic shower valves with a quarter turn ceramic disc headwork and/or a 2-way ceramic disc diverter headwork controlling the flow to 1,2 or 3 outlets with various operating members (see model). Temperature is controlled independently via a thermostatic cartridge with various operating members (see model) incorporating a manual override button Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of thermostatic mixing valves with DZR brass bodies. The inlets incorporate a stainless-steel strainer and single check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of wall mounted thermostatic bar shower mixers incorporating a non-rising spindle headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge that incorporates a manual override button. Both using either dome, cubed or single lever type operating members. The inlets incorporate stainless steel strainer washers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower hose, handset and riser rail assembly. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of wall mounted thermostatic bar shower mixers (brass bodies – various finishes) incorporating a ceramic cartridge headwork that controls the flow and diverts form hand shower to overhead shower outlet. The temperature is controlled independently via a thermostatic cartridge with dome or cubed type operating members that incorporate a manual override button. The inlets incorporate approved single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection. Supplied with a hose, handset and overhead shower outlet. Maximum working pressure 10.0 Bar Maximum operating temperature 60 °C.
Range of lever operated butterfly valves incorporating fusion bonded Epoxy coated ductile iron bodies, with stainless steel discs and end faces and EPDM seat. For use with Stainless steel pipe manufactured to EN 10217-7 (or Equivalent). For above and Below ground. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Wall mounted concealed two way and three way diverter valve assembly (brass bodies with trim sets in various finishes). The 59556 000070 and 59548 000170 concealed installation units are not approved in their own right. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of in-line, manually adjustable pressure reducing valves with DZR brass bodies. The RP1XX and RP2xx models can be supplied with a low- or high-pressure spring. The RP800 model is only available with a high-pressure spring. The RP1XX and RP2xx models can be pre-set from the factory at any value between the spring adjustment range (see below), e.g., the RP135 model will have a high-pressure spring and is pre-set at 3.5 bar. The RP800 is provided pre-set from the factory at 2.8 bar. Maximum inlet supply pressure 5.0 bar. Low-pressure spring adjustment range between 1.0 bar - 2.0 bar. High-pressure spring adjustment range between 2.1 - 5.0 bar. Cold water use only.
Range of bronze swing gate valves with bronze bodies and discs (with a metal-to-metal seal). Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of spherical ball valves having brass, DZR brass or stainless-steel bodies and lever type operating members. For use with stainless steel pipe (EN10312) or copper pipe (EN1057). Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C.
Range of spherical valves with DZR brass bodies, chrome plated brass balls and PTFE seats. The products incorporate a lever type operating members. Maximum working pressure 40.0 bar. Maximum operating temperature 100°C.
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass or brass bodies with chromium plated brass balls. Models incorporate lever or butterfly operating members. Maximum working pressure 10.0 Bar, 16 bar, 25 bar, 32 bar, 40 bar or 64 bar. Maximum operating temperature 100 °C.
Range of spherical valves, with DZR brass bodies and chromium plated brass balls. The products can be supplied with various operating members (see model). Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with bronze bodies incorporating a brass or stainless-steel ball with PTFE seat. Maximum operating pressure - 40 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with nickel plated brass bodies Max working pressure: 20 bar. Max operating temperature: 85°C.
Range of plastic bodies spherical valves (black, white and grey) incorporating either a screwdriver slot, lever or handwheel operating member (model specific). The pushfit connections are for use with DM LLDPE tubing (not supplied) and PEX barrier pipe (manufactured to BS7291-3). When used with DM LLDPE tubing (not supplied) the supplied black or grey pipe inserts must be installed. When used with PEX barrier pipe the supplied beige pipe inserts must be installed. Maximum working pressures and temperatures: When used with DM LLDPE tubing: Grey body valves, for sizes 6-15mm and ¼”-½” pushfit: 12.0 bar, cold water use only. Grey body valves, for sizes 6-12mm and ¼”-½” pushfit: 7.0 bar @ 65°C. Black and white body valves, for sizes 6-15mm and ¼”-½” pushfit: 12.0 bar, cold water use only and 7.0 bar @ 65°C. When used with PEX Barrier pipe (manufactured to BS7291-3): Grey body valves, for sizes 15-22mm, 5/8” and 7/8” pushfit: 12.0 bar, cold water use only. Black and white body valves, for sizes 15-22mm, 5/8” and 7/8” pushfit: 12.0 bar, cold water use only and 7.0 bar @ 65°C. All fittings which incorporate a barbed end connection are open outlet use only.
Range of gate valves with brass bodies, bronze bonnet, EPDM ‘O’-ring and PTFE seat. The valves are operated via a non-rising stem and a handwheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Page 67 of 71
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
