Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 630LT'. Factory applied, two-part, white coloured epoxy coating. Mix base and cure agent in a 3:1 volume ratio and apply as per manufacturer's PDS dated November 2024. Cure for 3 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'H-451PW'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user manual 'TWJ/H--451PW-20250120', dated 'January 1, 2025'. Cure for 7 days for 25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TS2160'. Factory applied, grey coloured, enamel coating intended to line glass fused steel tanks. Apply two coats as per manufacturer's Work Instructions 'AQ 10 07 Rev.1'. Fire for 10 minutes at 840°C. For use with water up to 23°C. This material is only approved for the firing conditions that appear on the approval. If the firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZCGJ-2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'ZC02250725' dated '2025.7.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ZC-2025HSR'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio and apply as per manufacturer's instructions 'ZC01250725', dated '2025.7.25'. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 430'. Factory applied, two-part, white coloured epoxy coating. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's PDS dated 'December 2024'. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'8284873 HA002I INT 100 HYF WHITE SN80'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's TDS 'Revision Date: V2, 24.05.2024', 'Region: EMEA'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SF-CM1'. Factory applied, grey coloured, sulphate resistant cement mortar. Mix cement mortar, sand & water in a 2:1:0.4 mass ratio and apply as per manufacturer's user instructions 'SF-CM1', 'Vision A1' dated '2024-7'. Cure for 12 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 51 of 53
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
