Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'YS-01 Powder Coating'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instruction document 'HJ-Q-SOP-05' dated 2020-1-10. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Genesis FBE 5010'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS issued 'August 2025'. Cure for 10 minutes@200°C. For use with water up to 23°C.
'VPC5022 Signal Blue FBE'. Factory applied, blue coloured Epoxy powder coating. Pre-heat substrate to 200°C and dip apply coating in a fluidised bed as per manufacturer's Product Data Sheet 'VPC5022', 'Revision: 1', dated '3 November 2025'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VPC8001 Gloss Black FBE'. Factory applied, black coloured Epoxy powder coating. Pre-heat substrate to 200°C and dip apply coating in a fluidised bed as per Product Data Sheet 'VPC8001', 'Revision: 1', dated '3 November 2025'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Factory applied, two-part, black or white polyurethane coatings. 'Pentathane 1000 SD Black'. Mix parts A & B in a 2.5:1 volume ratio and apply as per ‘August 2022’. Cure for 7 days@25°C. For use with water up to 65°C. 'Pentathane 1000 SD Off White'. Mix parts A & B in a 3:1 volume ratio and apply as per ‘August 2022’. Cure for 7 days@25°C. For use with water up to 23°C.
'Abcite® 1060 DW Blue & Abcite® X60 DW Blue'. Factory applied, blue coloured thermoplastic powder coatings applied by dipping in a fluidised bed. Pre-heat substrate the coating is to be applied to for 12 minutes@280°C and apply as per manufacturer’s Application Guide ‘Version 04.05.2015’ (Abcite® 1060 DW Blue) or Technical Data Sheet ‘11/2023’ (Abcite® X60 DW Blue). Post-heat for 5 minutes@160°C. For use with water up to 23°C. These materials are only approved for the pre-heat and post-heat conditions that appear on the approval. If the pre-heat and/or post-heat conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'YHR-GFS Enamel'. Factory applied, dark blue coloured Enamel coating. Mix enamel powder with water in a ratio of 7:3 and apply two coats as per manufacturer's TDS 'YHRGFS2504', version 'V0', dated '2025/3/27'. Cure for 20 minutes@120°C and fire for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the mixing, curing & firing conditions that appear on the approval. If the mix and/or cure and/or fire conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fusion Bonded Epoxy (IMP-FBE) Cobalt Blue RAL 5013'. Factory applied, dark blue coloured epoxy coating. Pre-heat the substrate to 200°C and spray apply one coat at 120°C as per manufacturer's TDS 'YHRFBE2504', version 'V0'. dated '2025/3/27'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BFSC MAS S&MDN 25'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a mass ratio of 1:2.35:0.45 and apply as per manufacturer's TDS 'SGMAS20111012-01', dated '2011.10.12'. Cure for 19 hours@70°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-02 Portland Cement Mortar'. Factory applied, grey coloured Portland cement mortar. Mix cement:sand:water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue reference 'Ascent02-2511', dated '2025.11.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Page 50 of 52
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
