Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POLYGEL-2136'. Factory applied, two-part, white coloured (opaque) isophthalic gelcoat comprising of a resin and catalyst. Mix resin and catalyst in a 50:1 mass ratio and apply as per manufacturer's TDS 'Revision No. 10', dated 'SEPT 2024'. Cure for 3 hours@85°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jindal Saw Limited Ordinary Portland Cement - 53 Grade'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a xx ratio of 1:1.5:0.5 and apply as per manufacturer's Work Instructions 'JSAW/AP01/DISP/PRO/WI-09', version '2.0', effective date '01.05.2023'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C.
'RAL 5005 Epoxy Coating'. Factory applied, blue coloured Epoxy Coating. Apply as per manufacturer's TDS '31.05.2024'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LM-coat'. Factory applied, blue coloured, two-part Polyurea coating. Mix Part A (KOBECASE PS-6031) with Part B (COBENATE I-362) in a 100:100 volume ratio and apply as per manufacturer's TDS 'Rev. no: 02', dated '16.02.2022'. Cure for 4 hours@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ResiGard APUA (NT) Coating'. Factory applied, grey coloured (once mixed), two-component coating. Mix and apply as per Technical Data Sheet ‘PDS/RG37/Ver15/01/25’. Cure for 1 minute@25°C. For use with water up to 85°C.
'Greentech 5000'. Factory applied, blue coloured Epoxy powder coating. Apply as per manufacturer's 'GRHK/QES GL 2025' and cure for 10 minutes@200°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PolyQuick® P-500 PW'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 05-2025'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SOLID-01'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'SOLID-196', 'Vision: A-2', dated '2019-8-28'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PA6059 Pure Polyester Powder Coating'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions 'file no. FP180515 version 2' dated May 25, 2018. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 49 of 51
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
