'Twineflon® R12D06'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'EP12/2/5 BLK 'O'-rings & seals'. Black coloured, injection moulded EPDM 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.0mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
'EP701253C'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'XR0240012'. Black coloured, compression moulded EPDM material. Shore hardness 40. Tested in-radius size 1.5mm. For use with water up to 85°C.
'D0012'. Black coloured, EPDM rubber material manufactured by vulcanised moulding. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'Interflon Paste HT1200'. Cream coloured ceramic paste. Apply as per manufacturer's instructions, document number 'IFUHT1200' dated 24/04/2017. Cure for 5 minutes@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XFGJ-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X20220228F' dated '2022-2-28'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SPS-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'S20220601' dated '2022-6-1'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Range of stop valves with plastic bodies and an EPDM diaphragm. The valves are operated via a switch located on the valve. The RCL and RPL models can also be operated by a remote switch. The product incorporates a plastic strainer central to the body. All valves are for use with copper pipe (manufactured to BS EN 1057). The PL suffix valves are also for use with PEX pipe (manufactured to BS7291-3). Models added Jan 2025 are for use with PE80 & PE100 pipes manufactured to BS EN 12201:2 at the inlets and the outlets are suitable for PEX pipe manufactured in accordance with BS7291 and copper pipe manufactured in accordance with BS EN 1057. For above ground use only. Maximum working pressure 10.0 bar. Cold water use only.
Page 47 of 247
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
