'ELYDAN'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 40°C.
'+GF+ Hakan HDPE PE100 Pipes'. Extruded PE100 pipes which are either blue coloured or black coloured (with blue stripes). For use with water up to 23°C.
'BR-PE-100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'DELAV HDPE Pipe PE100' and 'DELAV HDPE Pipe PE100-RC'. Black coloured (with blue stripes), extruded PE pipes. For use with water up to 23°C.
'STAR Spigot Fittings'. Black coloured, extruded PE100 fitting. For use with water up to 60°C.
'GY-PEX-b(60-95)'. White coloured (translucent), extruded PEX hose. For use with water up to 85°C.
'Uponor Aqua Pipe'. Extruded, multi-layered PE-X pipe comprising of an off-white inner layer, black middle layer and white outer layer. For use with water up to 70°C.
'TORELINA® A670MWR1B'. Dark grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Visulfon' range of injection moulded PPSU materials which includes grades: K002 A8Y-G0048 (off-white). K002 BK001 (black). B002 NC001 (natural, appears amber). B002 BK001 (black). B002 A8Y-G0048 (off-white). For use with water up to 85°C.
'Amodel DW-1140 BK 938 & Amodel DW-1150 BK 938'. Black coloured, injection moulded PPA materials. For use with water up to 85°C.
'AquaTerra SDR 6 PP-R Pipes'. Green coloured, extruded PP-R pipes. 'AquaTerra SDR 7.4 PP-R Pipes', green coloured, extruded PP-R pipes were added to the approval in September 2024. All pipes are or use with water up to 85°C.
'+GF+ Hakan Aquasystem Faser Composite Stabil Pipe'. Multi-layered, extruded PPR pipe consisting of a white coloured inner, green coloured middle and white coloured outer layer. The following multi-layered, extruded PPR pipes were added to the approval in April 2025: Green coloured inner, green coloured middle and green coloured outer layer. Beige coloured inner, green coloured middle and beige coloured outer layer. Grey coloured inner, green coloured middle and grey coloured outer layer. For use with water up to 85°C.
'ISOGLASS H8C 4036U NA'. Cream coloured, injection moulded polypropylene material. For use with water up to 85°C.
'PTFE G300 Seat'. White coloured, extruded PTFE seat component. For use with water up to 85°C.
'Hepworth uPVC Pressure pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 50°C.
'Sylglas Plumber Fix Copper`. Site applied, copper coloured epoxy putty. The putty should be kneaded together, its supplied in a pre-measured 1:1 mass ratio and applied as per manufacturer's directions for use dated August 9th, 2021. Cure for 24 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPIT ViPer XTREM'. grey coloured (once mixed), two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'VIPER XTREM | 2023-1'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RAMSET ChemSet 801 Xtrem XC²'. Grey coloured coloured, two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'August 15, 2018'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TELCOR THL FGEB 80G NC'. Black coloured, calendered, natural rubber material. Shore hardness 80D. Tested in-radius size 1.2mm. For use with water up to 23°C.
'E7108 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'E7108 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
Page 437 of 566
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
