Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'APLICAPROOF PUA P'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'Rev - 06/2024'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APLICAPROOF PU W'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS 'Rev -06/2024'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hempadur 35560 Cream Coating with Hempadur 15590 Red Primer'. Factory applied, cream coloured, two-component epoxy coating for use with epoxy primer. ‘Hempadur 15590 Red Primer’ is a two-component primer to be mixed in a 15:4 volume ratio and applied as per manufacturers PDS dated ‘October 2024’. Cure for 16 hours@20°C. 'Hempadur 35560 Cream’ is a two-component coating to be mixed in a 6.8:2 volume ratio and applied as per manufacturers PDS dated ‘May 2024’. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JAZLINE DW'. Factory applied, two-component, light green coloured epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's TDS issued '1 / 2022'. Cure for 7 days@28°C. For use with water up to 60°C.
'P • HSR42.5'. Factory applied, grey coloured Sulphate resistant Portland cement. Mix cement:medium sand:water in 1:1.4:0.45 weight ratio and apply as per manufacturer's instructions 'Version 03', dated '29th-07-2024'. Cure for 3 hours at 25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TC-7808-19'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's data sheet dated June 8, 2019. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe IL 6001-120S'. Factory applied, blue coloured, fusion bonded epoxy powder coating. Pre-heat substrate to be coated for 15 minutes@200°C and coating applied as per manufacturer's TDS dated '22 August 2018'. Post-cure for 15 min@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chosui Coat Grey'. Factory applied, grey coloured (once mixed and applied), two-component epoxy resin coating, Mix base:hardener in a 2:1 weight ratio and apply as per PDS 'CN：IF438122003', dated '03/06/2022'. Cure for 7 days@30°C and then 7 days@60°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubota Powder TK1413F (SPD)'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's TDS 'RP23242', dated 'December 26, 2023'. Cure for 6 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubota Powder TK1413F I'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's PDS '4384-23-403' dated '2023/11/16'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 42 of 53
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
