Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Loctite EA 109'. Factory applied, grey/beige coloured, heat cured epoxy coating. Apply as per manufacturer's TDS for Loctite ESP109 (product has changed name) dated July 2007. Cure for 2 hours@130°C. For use with water up to 85°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Loctite PC 7255 GN (Green) coating for use with Bonderite M-NT 1455-W primer'. Factory applied, green coloured, two-component epoxy resin coating. Prime the surface to be coated with the Bonderite primer wipe. Mix and apply as per manufacturer’s TDS dated October 2016. Cure for 7 days@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Balinit Milubia'. Factory applied, dark grey coloured, two layered coating system consisting of a titanium bottom layer & diamond like coating top layer. Apply as per manufacturer`s instructions '080224' dated 08-Feb-2024. No curing required. For use with water up to 85°C.
‘Endoprene® 85-20’. Factory applied, two component, beige coloured, solvent free polyurethane coating. Mix and apply as per Technical Data Sheet dated '09/09/2019'. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Zhenxin Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HY/NG' dated '2023-06-02'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PM6/35/7623 Vitreous Enamel Coating. Factory applied, blue coloured enamel coating. Apply and fire as per manufacturer's datasheet dated '01-2018' For use with water up to 85°C.
'18521 Kanepox Lining Free Blue for use with Kanepox Hardener 0362'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix 18521 Kanepox Lining Free Blue & Kanepox Hardener 0362 in a 3.5:1 volume ratio and apply as per manufacturer's datasheet ‘Rev. No. 11’ dated February 2018. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MY-5005'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's user manual 'rev: 1.0' dated 01/01/2018. For use with water up to 85°C.
'Jotapipe IL 6001-120S'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS dated 22nd August 2018. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Edelpoxy FN TM 142'. Factory coloured, red coloured epoxy resin coating consisting of a base and hardener. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's IFU 'PCC/ PC 142', dated '10.07.2018'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 39 of 51
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
