Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'JBG-SRPC Plus'. Factory applied, sulphate resisting Portland cement intended to line ductile iron pipes. Mix sand:cement:water in a 3:2:1 ratio and apply as per manufacturer's instructions 'JBIL/IFU-01' dated '29.01.2024'. Cure for 28 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JBG-OPC Plus'. Factory applied, grey coloured, ordinary Portland cement intended to line ductile iron pipes. Mix sand:cement:water in a 3:2:1 ratio and apply as per manufacturer's instructions 'JBIL/IFU-01' dated '29.01.2024'. Cure for 28 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LRPOLO22-V'. Factory applied, clear vinyl-ester resin. Apply as per manufacturer's TDS 'LRF-QAC-FM-003, Rev 02', dated '27th Dec 2022'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LRPOLO22-ISO'. Factory applied, yellow coloured Isophthalic Polyester Resin. Apply as per manufacturer's TDS 'LRF-QAC-FM-002, Rev 02', dated '27th Dec 2022'. Cure for 24 hours@25°C. For use with water up to 45°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NATZINC EP9015 SC PART A-BI.5431 Primer for use with HYDRALFUN AC BLEU PAM RAL5005-CZL8190 Coating’. Factory applied, dark blue coloured (once applied), powder coating for use with two-part epoxy primer. Mix parts A & B of primer in a 100:10 mass ratio and apply as per manufacturer’s TDS dated February 2024. Cure for 24 hrs at 20°C. Apply coating as per manufacturer’s TDS dated February 2024 and cure for 21 days at 20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'file no. I01-KAJ1207' dated '2019.1.14'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'OBE-5378'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user instructions 'OBE-HG-001', edition 'A1', issue date '2023-OCT.-11st'. Cure for 10 minutes at 190°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JM 9-2910'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'edition no.1', issue date 2019-9-5. Cure for 15 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's TDS dated '24/11/2021'. For use with water up to 85°C.
'TEFRO®cor 150SW-LV'. Grey coloured, factory applied epoxy coating. Mix in a 6:1 weight ratio (4:1 volume ratio) and apply as per manufacturer's Product Data Sheet, 'Revision Status 02/11/2023'. Cure for 7 days at 23°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 36 of 51
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
