Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'APCOSHIELD FBVL EX400G – RAL 5005 Blue & RAL 5017 Blue'. Factory applied, blue coloured epoxy coatings. Apply as per manufacturer’s datasheet ‘PDS/APPPG/V01/01-2024’. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APCOSHIELD FBPC EX405SG INTER GREEN'. Factory applied, green coloured epoxy coating. Apply as per manufacturer's data sheet 'PDS/APPPG/V02/01-2024'. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 HT Red'. Factory applied, red coloured (once mixed), two-component epoxy coating. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's instructions 'Chembur R&D/PI/23/02' dated 28/12/2023. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotun Marathon IQ2'. Factory applied, two-component, grey coloured epoxy coating. Mix parts A:B in a ratio of 3:1 parts and apply as per 'Jotun Marathon IQ2' Technical Data Sheet dated '16 April 2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'G52-06 Quick-drying type Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured polyethylene coating. Apply as per manufacturer's data sheet 'XYJSMS002', dated January 10th, 2023. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 200 K Grey’ for use with ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. ‘SIGMAPRIME 200 K Grey’ (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio and applied as PDS ‘7416’, dated February 25, 2021. Cure for 24 hours@23°C. ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’ is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio and applied as PDS ‘7785’, dated August 19, 2022. Cure for 12 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI Hygienic CML'. Factory applied, grey coloured cement mortar. Mix cement mortar:sand:water in a weight ratio of 36:46:18 and apply as per manufacturer's instructions 'LMICMA012624', dated '1/26/2024'. Cure for 20 hours@40°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Alsen FBE Blue Powder Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's Product Data Sheet 'AIPL 1212/1', dated '07/06/2023'. Cure for 2.5 hours:235°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSC-01'. Factory applied, grey coloured cement mortar. Mix sand:water: cement in a 1.5:1.0:1.0 weight ratio and apply as per manufacturer's instructions 'GB0012023', edition 'A1'. dated '2023-10-10'. Cure for 24 hours at 25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LUBERPOX-2K-DS-LACKFARBE (IV81 & IW81)’ – blue coloured and ‘LUBERPOX-2K-DS-LACKFARBE (IV81812 & IW81)’ – red coloured’. Factory applied, two component, epoxy coatings consisting of IV81 or IV81812 (base) and IW81 (hardener). Mix IV81 or IV81812 (base) & IW81 (hardener) in a mass ratio of 5:1 or volume ratio of 3.5:1 and apply as per manufacturer’s data sheets ‘Rev: 04 – 04.12.2023’ (blue) or ‘Rev: 03 – 04.12.2023’ (red). Cure for 20 minutes@22°C and then 40 minutes@75°C. For use with water up to 65°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Page 35 of 51
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
