Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
'ANUBIT HB-1000'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's TDS 'AE-TDS-023-2021', dated '02.08.2024'. Please note that use of a thinner isn't covered by the scope of this approval. Cure for 40 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
NY Blue PP. Blue coloured, factory applied nylon powder coating. Apply as per manufacturer's instructions for 'NY Blue PP nylon powder' dated 01-05-25, then post cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AMMT-021'. Factory applied, yellow coloured, two-component polyurethane coating. Components A and B are preheated to 65°C and then mixed & sprayed (using a thermal spraying instrument) in a volume ratio of 1:1 according to Application Instructions dated 'APR 2013'. Cure for 7 days@23°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-010Y'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'JXT/JS02-10', edition '1/0', dated '2021-11-30'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ET-52184 & ET-52185'. Factory applied, black coloured water-based silicone coating comprising of an under-coat (ET-52184) and finishing coat (ET-52185). Apply as per manufacturer's instructions 'V8.2' issued January 2019. Cure both undercoat and finishing coat for 10 minutes@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hostalen PP H2142 12'. Black coloured, injection moulded and compression moulded polypropylene material. For use with water up to 23°C.
'R210WM'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies, various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Depending on model the products are supplied with either a stainless steel braided PEX lined flexible hose assembly with 15mm spigot end connection or 10mm copper tail (see models). Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Page 336 of 350
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
