'PT-EPDM55'. Black coloured, compression moulded EPDM material. Shore hardness 55. Tested in-radius size 1.1mm. For use with water up to 60°C.
'AEC.5/EPDM.80'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.1mm. For use with water up to 65°C.
'EPDM 773'. Black coloured, injection moulded EPDM sheet material (manufactured in Czech Republic). Shore hardness 50. Tested in radius sizes 0.9mm. For use with water up to 23°C.
'EPDM 798'. Black coloured, injection moulded EPDM material (manufactured in Czech Republic). Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Kingsun EP1702'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'XXE01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'JM-EP01'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Sunaflex T 8193'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AquaFlex T 5893'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'AquaFlex T 9696'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'210N' components. Black coloured, injection moulded NBR rubber ‘O’ rings, washers and lip seals. Shore hardness 70. The ‘O’ rings have an in-radius of 1.31mm, the washers 1.05mm and the lip seals 0.45mm. For use with water up to 60°C.
'ELASTOSIL LR 3020/60 A+B' Natural (appears white, translucent) & 'ELASTOSIL LR 3020/60 A+B with 2% by weight ELASTOSIL Colour Paste FL Red Iron Oxide RAL 3013' (red coloured). Injection moulded silicone rubbers with a shore hardness of 60 ShA and a tested in-radius size of 0.9mm. For use with water up to 85°C.
'Supercast PVC Waterstop Hydrofoil'. Blue coloured, extruded PVC waterstop. For use with water up to 23°C. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The materials have been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1
'Wiseman Everblue Jointing Compound'. Beige coloured jointing compound. Apply as per manufacturer's instructions '001/A2'. For use with water up to 85°C.
'Weld-On 719 ECO'. Uncoloured, transparent PVC solvent cement. Apply as per manufacturer's product data sheet '719 ECO EU 07-2023'. Cure for 30 minutes@4°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JIYOU TPE-GE65011-BL (blue coloured), GE65011-GY (grey coloured), GE65011-WE (white coloured) & GE65011-BK (black coloured)'. Injection moulded, TPE materials. Shore hardness 60. In-radius size 1.1mm. For use with water up to 75°C.
Single hole, triple outlet (swivel) combination tap assembly (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with single lever operating member. Electronic controls allow the tap to dispense boiling, chilled or sparkling water. The vented models are supplied with a brass adaptor containing a plastic flow regulator and a combined EPDM washer and stainless-steel strainer, for installation on the mains cold water into the ceramic cartridge. They are also supplied with a stainless steel braided PEX lined flexible hose assembly and a stainless steel braided TPSiV lined flexible hose assembly both with ½” captive nut end connections for installation between the tap and a command centre, (which is not included as part of this approval). Maximum working pressure 5.0 bar. Maximum operating temperatures: Near boiling water circuit: 100°C. Ambient hot and cold (mixed) circuit: 65°C. Chilled/Chilled and sparkling circuit: Cold water use only.
Range of in-line, non-verifiable single check valve assemblies consisting of a spring loaded, resilient trim, single check valve cartridge housed within a DZR brass body. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of plastic aerators. Aerators which include ‘gpm max’ in the model name, incorporate a plastic flow regulator. Maximum operating temperature 60°C
Range of push button ceramic cartridge headworks with a plastic body and EPDM seals. For insertion into specifically dimensioned tap assemblies Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Page 322 of 566
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
