'SOFTPEX V® hose inliner'. Off white coloured (translucent), extruded polyethylene hose. For use with water up to 70°C.

Section:

5240 Polyethylene

Section Subtitle:

Components. All components listed in this section have been tested for water contact suitability of material only.

WRAS Approval Number:

251155039

Expiry date:

30/11/2030

Approval Holder:

Neoperl GmbH

Company Name

Neoperl GmbH

Address

Klosterrunstrasse 9-11, Müllheim

Postcode

D-79379

Country

Germany

Phone

+49 7631 188 374

General Email

DE.Approvals@neoperl.com

View All Listings by this Company

'RAMSET ChemSet™ Reo502™ Xtrem™’ & ‘RAMSET ChemSet™ Epcon™ G5 Xtrem™'. Site applied, brick coloured (once mixed), chemical anchor resins, each supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'NOV. 25'. Cure for 24 hours@21°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5311 Resin Anchors

Expiry date:

31/10/2030

Approval Holder:

RAMSET (ITW Australia)

Company Name

RAMSET (ITW Australia)

Address

1 Ramset Drive, Chirnside Park, Vic 3116

Country

Australia

View All Listings by this Company

'EP2504 (NSF)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.20mm. For use with water up to 85°C.

Section:

5365 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

251155042

Expiry date:

30/11/2030

Approval Holder:

Frick Flow-Tech Wuxi Co., Ltd.

Company Name

Frick Flow-Tech Wuxi Co., Ltd.

Address

No.50 Chunjiang Road, Industrial Park 9-3, Heqiao Town, Yixing City, Jiangsu Province

Country

China

View All Listings by this Company

'Effast Tite'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions 'PLUMEFF', dated '2024/09/17'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5560 Solvent Cements

Expiry date:

31/10/2030

Approval Holder:

Polypipe Italia s.r.l.

Company Name

Polypipe Italia s.r.l.

Address

Loc. Pianmercato 5C-D-H Cicagna

Country

Italy

General Email

Christopher.sanguineti@effast.com

View All Listings by this Company

Range of floor mounted, single hole, single outlet combination tap assemblies (stainless steel body – various finishes) incorporating a ceramic cartridge headwork and manual diverter to shower outlet, with single lever operating members. The spout outlets incorporate a plastic aerator. Product incorporates an approved check valve cartridge at the inlet; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Shower hose and handset is not supplied with this product. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0463 Combination Tap Assemblies

Section Subtitle:

Single hole tap(s) with a single outlet and a fixed spout, incorporating a manual diverter to a shower outlet.

WRAS Approval Number:

251108009

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (F).

Marking:

BAGNODESIGN on body.

Installation Requirements:

R001 R010 R020

Expiry date:

30/11/2030

Model:

BDM-STU-431-xx. XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C) & Truffle (TF-C).

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company