‘Sabic R50035EE’. ‘RX 806 Natural, RX 806 Black 9003, RX 806GR Black 9003, RX 820 Light Blue 6001 & RX 820GR Light Blue 6001’. Natural (appears white coloured), black and light blue coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘4TECH 9S22110 W-A ANL, 4TECH 9S22120 W-A ANL & 4TECH 9S22130 W-A ANL’: Yellow/brown coloured, injection moulded, glass filled PPO/HIPS materials. For use with water up to 85°C.
‘Wouper EG30WF, EG40WF & EG50WF’. Injection moulded, glass filled (30% - 50%) PPA materials available in natural (appears off-white), black and grey. ‘Wouper EG30WF, EG40WF & EG50WF’ natural, black & grey are for use with water up to 85°C. ‘Wouper AG30WF’. Injection moulded, glass filled (30%) PPA materials available in natural (appears off-white), black & grey. ‘Wouper AG30WF’ natural & black are for use with water up to 85°C. Between July 2022 and January 2023, ‘Wouper AG30WF’ grey is for use with water up to 23°C. From February 2023, ‘Wouper AG30WF’ grey is for use with water up to 85°C.
'TCM585RE'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '21.07.2021'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GDE 7133', black coloured, compression moulded EPDM 'O' ring with a tested in-radius size of 2.0mm. In March 2025, ‘KD S-Ring’. black coloured, compression moulded EPDM seal with a tested in-radius size of 0.95mm was added to the approval. Both components have a shore hardness 70 and are for use with water up to 85°C.
'D0012'. Black coloured, EPDM rubber material manufactured by vulcanised moulding. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘Addisil 1050E, 1060E, 1070E & 1080E’. Un-pigmented (appear white in colour), translucent, extruded, silicone rubber sheet materials. Shore hardness between 50 & 80. Tested in-radius size of 2.1mm. For use with water up to 85°C.
'Addisil 2050E, 2060E, 2070E & 2080E'. Unpigmented (appear white, translucent), extruded silicone rubber materials. Shore hardness between 50 & 80. Tested in-radius size of 2.1mm. For use with water up to 85°C.
'Rapidstick™ 8243’ Site applied, blue coloured anaerobic adhesive. Apply and cure as per manufacturer's instructions. 'Rapidstick™ 8243' is for use with water up to 85°C.
‘PK-HM 8 natural (6145) & PK-VM 8 natural (6146)’. Natural (appear beige in colour), injection moulded polyketone materials. For use with water up to 85°C.
Page 231 of 779
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
