'PTFE FE 1000'. White coloured, compression moulded PTFE material. For use with water up to 85°C.
'Sigma 511 (pink), Sigma 500 (blue) and Sigma 588 & 600 (white)'. PTFE sheet materials manufactured by calendaring & sintering. For use with water up to 85°C.
'LIP/PTFE/875'. Site applied, pre-mixed, injectable PTFE/Silicone Grease sealing compound. Extrude and apply the pre-mixed compounds as per manufacturer's work instructions document 'STS-MS-001', revision '01', dated 11/08/23. No cure required. For use with water up to 23°C.
'REGJ01'. Black coloured, extruded silicone rubber tape. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'TCM585RE'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '21.07.2021'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘2KPS EASF-VE’. Site applied, two part, grey coloured anchor resin. 2KPS EASF-VE is light grey coloured when mixed and consists of Part A (shiny grey coloured liquid) & Part B (shiny off-white coloured liquid). Mix, apply and cure as per manufacturer’s product information sheet 'EASF-V / VC / VE (EU07) V4.0'. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'XGM050'. Black coloured, compression moulded EPDM rubber gaskets manufactured from raw material '70802'. Shore hardness 80. Tested in-radius size 2.5mm. For use with water up to 85°C.
'4360 'O' rings, washers, membranes and lip seals'. Black coloured, injection moulded EPDM components with a shore hardness of 60. The ‘O’ rings have a tested in-radius size of 1.31mm. The washers have a tested in-radius size of 1.05mm. The membranes have a tested in-radius size of 1.55mm. The lip seals have a tested in-radius size of 0.40mm. For use with water up to 85°C.
'7EP1197 Gasket'. Black coloured, extruded EPDM gasket. Shore hardness 70. Tested in-radius size 0.5mm. '7EP1197 'O'-rings' were added to the approval in March 2023. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'EP 856 gaskets and 'O'-rings'. Black coloured, injection moulded 'O'-rings with a tested in-radius size of 0.9mm. Black coloured, extruded gaskets with a tested in-radius size of 0.5mm. Both gaskets and 'O'-rings have a shore hardness of 80 and are for use with water up to 85°C.
'KEP EPDM Butterfly Valve Seat'. Black coloured, compression moulded EPDM sheet. Shore hardness 70. Tested in-radius size 1.6mm. For use with water up to 23°C.
'EP0B7070C 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.5mm. For use with water up to 23°C.
'EP01961PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CVE78'. Black coloured, extruded EPDM material. Shore hardness 80. Tested in-radius size 10.0mm. For use with water up to 23°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EPH-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘KRE 60 (103), KRE 65 (100) & KRE 65 (106)’. In September 2022 ‘KRE 60 (104)’ was added to the approval. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60 & 65. Tested in-radius size 1.0mm. For use with water up to 60°C.
'TIMO 3-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EX60LC, EX70LC & EX80LC'. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60, 70 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'HT5697-5'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 1.0mm. For use with water up to 50°C.
Page 197 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
