'Poly Alsharif Fittings'. Green coloured, injection moulded PPR fittings. For use with water up to 80°C.

Section:

5260 Polypropylene

Section Subtitle:

Components.

WRAS Approval Number:

260155047

Expiry date:

31/01/2031

Approval Holder:

Alamal Alsharif Plastics

Company Name

Alamal Alsharif Plastics

Address

10th of Ramadan, 3rd Industrial zone A3, A3

Country

Egypt

View All Listings by this Company

'Smart S-IRE'. Site applied, light pink coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 17/0187’, dated ‘29/11/2023’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.

Section:

5311 Resin Anchors

Expiry date:

31/08/2030

Approval Holder:

PGB-Polska

Company Name

PGB-Polska

Address

Ul. Fryderyka Wilhelma Redena 3, 41-807 Zabrze

Country

Poland

View All Listings by this Company

‘AquaFlex T 5818’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 23°C.

Section:

5365 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

251255070

Expiry date:

31/12/2030

Approval Holder:

Compounds AG

Company Name

Compounds AG

Address

Barzloostrasse 1, 8330 Pfaffiken ZH, Switzerland

Phone

+41 44 953 34 36

General Email

info@compounds.ch

View All Listings by this Company

'01/T60FKM 'O' rings and gaskets' – for use with water up to 23°C. 01/T70FKM & 01/T80FKM 'O' rings and gaskets' – for use with water up to 85°C. Green coloured, injection moulded FKM 'O' rings and gaskets. Shore hardness between 60 & 80. In-radius size between 0.5mm & 3.5mm.

Section:

5370 Rubbers

Section Subtitle:

Fluoroelastomers - components.

WRAS Approval Number:

260155051

Expiry date:

31/01/2031

Approval Holder:

LAV.EL. Gomma Srl

Company Name

LAV.EL. Gomma Srl

Address

Via Aldo Moro 20/22 25033 - Cologne (BS)

Country

Italy

Phone

0039.030.70.50.956

General Email

info@lavelgomma.it

View All Listings by this Company

Range of side entry BS1212-4 (2016), delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 Bar Maximum operating temperature Cold water use only.

Section:

2075 Float Operated Inlet Valve

Section Subtitle:

Can be used to achieve a recognised air gap arrangement, providing it meets the appropriate backflow requirements. Suitable for use in a WC suite, provided it forms an arrangement which meets the requirements of Type AUK1 air gap and an appropriate WC performance specification.

WRAS Approval Number:

251102048

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Model M3230WR can be supplied with either a brass or plastic ½” connection, a plastic 3/8” connection and either delayed or non-delayed action type float valve.

Size:

3/8” BSP (M) 1/2” BSP (M) (brass or plastic inlet connection)

Marking:

Miellat, Model number & BS1212-4 on body.

Installation Requirements:

R001 R550

Expiry date:

30/11/2030

Model:

M3230WR

Approval Holder:

Miellat Industries LLC

Company Name

Miellat Industries LLC

Address

Unit B-24, KEZAD Logistics Park, 2 Al Zaeem St, Khalifa Industrial Zone Abu Dhabi

Country

U.A.E

General Email

info@miellat.com

View All Listings by this Company