'CORE PTFE Tape'. White coloured (semi-translucent), extruded PTFE tape. For use with water up to 85°C.

Section:

5294 Polytetrafluoroethylene (PTFE)

Section Subtitle:

Components.

WRAS Approval Number:

2309554

Expiry date:

30/09/2028

Approval Holder:

Smith Brothers Stores Limited

Company Name

Smith Brothers Stores Limited

Address

Unit V2 Winchester Avenue, Blaby, Leicester

Postcode

LE8 4GZ

View All Listings by this Company

'MasterCrete ANC 932'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1' dated '09.12.2024'. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5311 Resin Anchors

Expiry date:

31/10/2028

Approval Holder:

Master Builders Solutions España, S.L.U.

Company Name

Master Builders Solutions España, S.L.U.

Address

Carretera de l’Hospitalet, 147-149, Edificio Viena, 1ª planta 08940 Cornellà de Llobregat, Barcelona

Country

Spain

View All Listings by this Company

'E7331'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.8mm. For use with water up to 85°C.

Section:

5360 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - components.

WRAS Approval Number:

2308558

Expiry date:

31/08/2028

Approval Holder:

Ulman Dichtungstechnik GmbH

Company Name

Ulman Dichtungstechnik GmbH

Address

Max-Planck-Strasse 32, 71116 Gartringen

Country

Germany

View All Listings by this Company

‘0548’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.

Section:

5365 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2303560

Expiry date:

31/03/2028

Approval Holder:

Wilhelm Kachele GmbH

Company Name

Wilhelm Kachele GmbH

Address

Jahnstrasse 9, D-73235 Wilhelm Teck

Country

Germany

Phone

Tel: +49 7023 2038 Fax: +49 7023 103 188

View All Listings by this Company

'EP80R-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 50°C.

Section:

5365 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

241055077

Expiry date:

31/10/2029

Approval Holder:

ATUSA GRUPO EMPRESARIAL, S.A.

Company Name

ATUSA GRUPO EMPRESARIAL, S.A.

Address

Pol. Industrial ATUSA-Agurain, S/N 01200 Salvatierra (Álava- España)

Phone

+34 945 18 00 00

General Email

info@atusa.es

View All Listings by this Company