'Hempadur 35560 Cream Coating with Hempadur 15590 Red Primer'. Factory applied, cream coloured, two-component epoxy coating for use with epoxy primer. ‘Hempadur 15590 Red Primer’ is a two-component primer to be mixed in a 15:4 volume ratio and applied as per manufacturers PDS dated ‘October 2024’. Cure for 16 hours@20°C. 'Hempadur 35560 Cream’ is a two-component coating to be mixed in a 6.8:2 volume ratio and applied as per manufacturers PDS dated ‘May 2024’. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

241055069

Expiry date:

31/10/2029

Approval Holder:

Hempel A/S

Company Name

Hempel A/S

Address

Lundtoftegaardsvej 91, 2800 Kgs. Lyngby

Country

Denmark

View All Listings by this Company

'JAZLINE DW'. Factory applied, two-component, light green coloured epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's TDS issued '1 / 2022'. Cure for 7 days@28°C. For use with water up to 60°C.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

241155018

Expiry date:

30/11/2029

Approval Holder:

Jazeera Factory for Paints Co.

Company Name

Jazeera Factory for Paints Co.

Address

PO Box 1900, Khamis Mushayt, 61961

Country

Saudi Arabia

View All Listings by this Company

'Enviroline 2405'. Site applied, off-white coloured (once mixed and applied), two-component epoxy. Mix parts A (light grey, opaque liquid) and B (white, opaque liquid) in a volume ratio of 2:1 and apply as per manufacturer's TDS 'Ref:10139', 'Issue Date:8/21/2017'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

240855046

Expiry date:

31/08/2029

Approval Holder:

Akzo Nobel Saudi Arabia Ltd.

Company Name

Akzo Nobel Saudi Arabia Ltd.

Country

Saudi Arabia

View All Listings by this Company

'novapress® 880'. Beige coloured fibre gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.

Section:

5075 Fibre

Section Subtitle:

These materials are for use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.

WRAS Approval Number:

241055050

Expiry date:

31/10/2029

Approval Holder:

Frenzelit GmbH

Company Name

Frenzelit GmbH

Address

Frankenhammer, 95460 Bad Berneck, Germany

Phone

Tel: 0049 9273 720 Fax: 0049 9273-222

View All Listings by this Company

'ELS 108 & ELS 101'. Extruded, multi-layered hoses comprising of a black coloured PVC inner layer, white coloured polyester middle layer and grey coloured PVC outer layer. For use with water up to 23°C.

Section:

5140 Hoses & Tubing

Expiry date:

31/10/2029

Approval Holder:

EL-SE Kablo ve Plastik Sanayi A.S.

Company Name

EL-SE Kablo ve Plastik Sanayi A.S.

Address

Geposb 11. Cadde No. 13, PK. 41400 Gebze

Country

Turkey

View All Listings by this Company