EP80/2 BLK 'O' rings & gaskets. Black coloured, injection moulded EPDM 'O' rings & gaskets. Shore hardness 80. Tested in-radius size 1.5mm. . For use with water up to 85°C.
`EP1/1/5 BLK 'O' rings, seals & gaskets'. Black coloured, injection moulded EPDM 'O' rings, seals & gaskets. Shore hardness 70. The 'O' rings & gaskets have a tested in-radius size of 1.5mm. The seals have a tested in-radius size of 0.8mm. For use with water up to 85°C.
'EUW-70'. Black coloured, injection moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 60°C.
`H34-50 to H34-70’. Range of black coloured, compression moulded EPDM rubber materials with a shore hardness of between 50 & 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP60-WAUK-FR'. Black coloured, compression moulded EPDM sheet material. Shore hardness 60. In-radius size 1.35mm. For use with water up to 23°C.
‘EPDM 825-c’. Black coloured, compression moulded EPDM sheet material. Shore hardness 80 A. Tested in-radius size 1.0mm. For use with water up to 23°C.
`SP402`. Black coloured, compression moulded, natural rubber material. Shore hardness 75. Tested in-radius size 1.00mm. For use with water up to 23°C.
'WN60/1 BLK 'O' rings'. Black coloured, injection moulded NBR 'O' rings. Shore hardness 60. Tested in-radius size 1.31mm. For use with water up to 60°C.
`WN 22/1/9 BLK` 'O' rings. Black coloured, injection moulded, nitrile rubber 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 65°C.
'LS80T-1201 White'. White coloured, injection moulded silicone rubber gasket. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'5080SIL310P‐N' (natural - clear) & '5080SIL310P‐B' (black coloured). Extruded, silicone rubber hoses. Shore hardness 70. Tested in-radius size 0.75mm. For use with water up to 85°C.
'AJSIL-001'. Natural (appears white in colour), compression moulded silicone rubber material. Shore hardness 50. Tested in-radius size 2.0mm. For use with water up to 85°C.
'Permabond 102, 240, 105 & 2010'. Site applied, single-component, colourless adhesive/sealants. Apply as per manufacturer’s technical data sheets. Cure for 24 hours at 22°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (either stainless steel or brass bodies in a variety of finishes). Flow is controlled via two solenoid valves (housed in a control box) activated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The temperature is controlled independently via a ceramic cartridge with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
BS EN 997:2018 RAK Compact Rimless Wall Hung 700mm COMRIMWH W.C. pan (Ceramic), Thomas Dudley ‘A’ frame incorporating a Thomas Dudley Vantage Concealed cistern with a side entry compact type float operated inlet valve which discharges via a Type AG airgap and a dual flush pneumatic drop valve capable of full flush volumes of 4.5 litres and a reduced flush of 3 litres. The inlet connection hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
DC type pipe interrupter with a permanent atmospheric vent and DZR brass body and EPDM gasket. Maximum working pressure 3.0 bar. Maximum operating temperature 85°C.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and NBR seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Spring loaded resilient trim, in-line check valve cartridges incorporating plastic guides and stem, NBR or EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of single check valve cartridges incorporating a plastic body, stainless steel spring, NBR or EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Page 11 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
